Fastener Tightening Specifications
WARNING: This page is about a different car, the 2007 GMC Yukon XL and 2007 Chevrolet Suburban. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Ref No.* | Qty | Size | Specification | |
|---|---|---|---|---|---|
| Metric | English | ||||
| Accumulator Housing to Valve Body | 53 | 6 | M6x1.0x100 | 11 N.m | 97 lb in |
| Case Center Support | 25 | 1 | 3/8-16x27.2 | 43 N.m | 32 lb ft |
| Control Valve Body to Case | 35 | 21 | M6x1.0x55 | 11 N.m | 97 lb in |
| Cooler Pipe Connector Nut to Case | 90 | 2 | 1/4-18NPS(SPL) | 38 N.m | 28 lb ft |
| Engine Rear Mount to Transmission Bolt | - | - | - | 44 N.m | 32 lb ft |
| Engine Rear Support Bracket to Frame Nut | - | - | - | 44 N.m | 32 lb ft |
| Extension Housing to Case | 21 | 6 | M10x1.50x30 | 34 N.m | 25 lb ft |
| Flywheel Housing Cover to Transmission | - | - | - | 7 N.m | 62 lb in |
| Flywheel to Convertor | N/A | 6 | M10x1.5x23 | 43 N.m | 32 lb ft |
| Fourth Clutch Housing | 26 | 1 | 5/16-18x24.4 | 23 N.m | 17 lb ft |
| Heat Shield to Transmission Bolts | - | - | - | 17 N.m | 13 lb ft |
| Line Pressure Test Hole Plug | 24 | 1 | 1/8-27NPTFx15.8 | 11 N.m | 97 lb ft |
| Manual Shaft Detent Lever Nut | 712 | 1 | M10x1.50x10.8 | 24 N.m | 18 lb ft |
| Oil Drain Plug | 79 | 1 | M12x1.75x19.3 | 34 N.m | 25 lb ft |
| Oil Pan to Case | 27 | 17 | M8x1.25x20 | 24 N.m | 18 lb ft |
| Oil Test Hole Plug | - | - | - | 11 N.m | 97 lb in |
| Parking Pawl Bracket to Case | 714 | 1 | M8x1.25x20 | 24 N.m | 18 lb ft |
| Pressure Control Solenoid Bracket to Valve Body | 310 | 1 | M6x1.0x19.6 | 8 N.m | 71 lb in |
| Pump Assembly to Case | 3 | 8 | M8x1.25x63 | 24 N.m | 18 lb ft |
| Pump Body to Cover | 220 | 5 | M8x1.25x40 | 24 N.m | 18 lb ft |
| Rear Servo Cover to Case | 61 | 6 | M8x1.25x20 | 24 N.m | 18 lb ft |
| Solenoid to Valve Body | 310 | 2 | M6x1.0x19.6 | 8 N.m | 71 lb in |
| Speed Sensor Bracket to Case | 23 | 2 | M6x1.0x14 | 11 N.m | 97 lb in |
| Transmission Case to Engine | - | - | - | 44 N.m | 32 lb ft |
| Transmission Mount to Transmission Bolts | - | - | - | 50 N.m | 37 lb ft |
| Transmission Mount Retaining Nut | - | - | - | 40 N.m | 30 lb ft |
| Valve Body to Case/Lube Pipe | 35 | 2 | M6x1.0x35 | 11 N.m | 97 lb in |
| Valve Body to Case/TFP | 76 | 6 | M6x1.0x55 | 11 N.m | 97 lb in |
| * Reference Number refers to the callout number on the disassembled view. | |||||