LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 130 (Theft Deterrent System) >> Diagnostic Information and Procedures >> Content Theft Deterrent (CTD) Does Not Disarm with Key Lock

Content Theft Deterrent (CTD) Does Not Disarm with Key Lock

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
Content Theft Deterrent (CTD) Does Not Disarm with Key Lock

Step Action Yes No
Schematic Reference: Theft Deterrent System Schematics 
Connector End View Reference: Displays and Gages Connector End Views
DEFINITION: The content theft deterrent (CTD) system does not disarm when the vehicle is unlocked with the key.
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Turn ON the ignition.
  2. With a scan tool, observe the door key switch parameter in the BCM data list.
  3. Insert the ignition key into the driver door key cylinder.
  4. Turn and hold the door key cylinder to the UNLOCK position.
  5. Repeat the procedure for the passenger door lock cylinder.
Does the scan tool display ACTIVE when the key cylinders are held in the UNLOCK position?		 Go to Testing for Intermittent Conditions and Poor Connections Go to Step 3 
3 Does the scan tool display INACTIVE when both the left door key cylinder and the right door key cylinder are held in the UNLOCK position? Go to Step 4  Go to Step 6 
4 Test the body control module (BCM) portion of the door key switch signal circuit for an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 12  Go to Step 5 
5 Inspect for a poor connection at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Was a condition found and corrected?		 Go to Step 12  Go to Step 11 
6
  1. Disconnect the one inoperative door key cylinder switch.
  2. Connect a 3-amp fused jumper wire between the door key switch signal circuit of the inoperative door key cylinder switch and a good ground.
  3. Observe the door key switch parameter on the scan tool.
Does the scan tool display ACTIVE?		 Go to Step 8  Go to Step 7 
7 Repair the open in the appropriate door key switch portion of the door key switch signal circuit.
Did you complete the repair?		 Go to Step 12  -
8
  1. Connect a 3-amp fused jumper wire between the door key switch signal circuit and the ground circuit.
  2. Observe door key switch parameter on the scan tool.
Does the scan tool display ACTIVE?		 Go to Step 10  Go to Step 9 
9 Repair the open in the ground circuit of the inoperative door key switch.
Did you complete the repair?		 Go to Step 12  -
10 Replace the inoperative door key switch. Refer to Door Lock Cylinder Replacement .
Did you complete the replacement?		 Go to Step 12  -
11 Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 12  -
12
  1. Reconnect any connectors that were removed for testing.
  2. Clear any DTCs that may have been set during this procedure.
  3. Attempt to arm the content theft deterrent (CTD) system.
  4. Simulate an intrusion.
Did you correct the condition?		 System OK Go to Diagnostic System Check - Vehicle
scientia non olet · About LEMON Manuals