LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 129 (Power Seat System) >> Diagnostic Information and Procedures >> DTC B1825, B1850, B1860, B2355, B2365, or B2375 >> Circuit/System Testing

Circuit/System Testing

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.

B1825

  1. Ignition OFF, disconnect the C2 harness connector at the seat recline motor.
  2. Ignition OFF, test for less than 2 ohms of resistance between the low reference circuit terminal 1 and ground.
    • If greater than 2 ohms, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
  3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 3 and ground.
    • If less than 4.8 volts, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the MSM.
    • If greater than 5.2 volts, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
  4. Verify the scan tool Driver Seat Recline Sensor parameter is less than 2.0 volts.
    • If greater than 2.0 volts, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the MSM.
  5. Install a 3A fused jumper wire between the signal circuit terminal 2 and the 5-volt reference circuit terminal 3. Verify the scan tool Driver Seat Recline Sensor parameter is greater than 4.65 volts.
    • If less than 4.65 volts, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the MSM.
  6. If all circuits test normal, test or replace the seat recline position sensor.

B2355/B2365/B2375

  1. Ignition OFF, disconnect the C2 harness connector at the seat adjuster motor assembly.
  2. Ignition OFF, test for less than 2 ohms of resistance between the low reference circuit terminal 2 and ground.
    • If greater than 2 ohms, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
  3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 6 and ground.
    • If less than 4.8 volts, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the MSM.
    • If greater than 5.2 volts, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
  4. Verify the appropriate scan tool Driver Seat Sensor parameter is less than 2.0 volts.
    • If greater than 2.0 volts, test the appropriate signal circuit for a short to voltage. If the circuit tests normal, replace the MSM.
    • Seat front vertical position sensor terminal 1
    • Seat rear vertical position sensor terminal 5
    • Seat horizontal position sensor terminal 3
  5. Install a 3A fused jumper wire between the signal circuit and the 5-volt reference circuit terminal 6. Verify the appropriate scan tool Driver Seat position sensor parameter is greater than 4.65 volts.
    • Seat front vertical position sensor terminal 1
    • Seat rear vertical position sensor terminal 5
    • Seat horizontal position sensor terminal 3
    • If less than 4.65 volts, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the MSM.
  6. If all circuits test normal, test or replace the seat adjuster motor assembly.

B1850/B1860

  1. Ignition OFF, disconnect the C2 harness connector at the seat lumbar motor assembly.
  2. Ignition OFF, test for less than 2 ohms of resistance between the low reference circuit terminal C and ground.
    • If greater than 2 ohms, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
  3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.
    • If less than 4.8 volts, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the MSM.
    • If greater than 5.2 volts, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
  4. Verify the appropriate scan tool Lumbar Sensor parameter is less than 2.0 volts.
    • If greater than 2.0 volts, test the appropriate signal circuit for a short to voltage. If the circuit tests normal, replace the MSM.
    • Lumbar vertical position sensor terminal B
    • Lumbar horizontal position sensor terminal D
  5. Install a 3A fused jumper wire between the signal circuit and the 5-volt reference circuit terminal C. Verify the appropriate scan tool Lumbar Sensor parameter is greater than 4.65 volts.
    • Lumbar vertical position sensor terminal B
    • Lumbar horizontal position sensor terminal D
    • If less than 4.65 volts, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the MSM.
  6. If all circuits test normal, test or replace the lumbar motor assembly.
scientia non olet · About LEMON Manuals