LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 115 (Antilock Brake System, Traction Control System & Stability Control System) >> Diagnostic Information and Procedures >> DTC C0161 (Over 8600 GVW) >> Test Description

Test Description

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 4:  This step tests for a shorted stop lamp switch.
  2. 5:  This step tests for an open stop lamp switch.
DTC C0161 (Over 8600 GVW)

Step Action Yes No
Schematic Reference: Antilock Brake System Schematics 
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Install a scan tool.
  2. Select the 4WAL 3 Sensor Data Display function.
  3. Observe the Brake Switch Status on the scan tool.
Does the scan tool display OFF?		 Go to Step 3  Go to Step 5 
3
  1. Apply the brake.
  2. Observe the Brake Switch Status on the scan tool.
Does the scan tool display ON?		 Go to Diagnostic Aids Go to Step 4 
4 
  1. Turn OFF the ignition.
  2. Disconnect the stop lamp switch. Refer to Stop Lamp Switch Replacement (Adjustable Pedal) or Stop Lamp Switch Replacement (Non-Adjustable Pedal) .
  3. Turn ON the ignition.
  4. Observe the Brake Switch Status on the scan tool.
Does the scan tool display ON?		 Go to Step 9  Go to Step 7 
5 
  1. Turn OFF the ignition.
  2. Disconnect the stop lamp switch. Refer to Stop Lamp Switch Replacement (Adjustable Pedal) or Stop Lamp Switch Replacement (Non-Adjustable Pedal) .
  3. Connect a fused jumper wire between the ignition 3 voltage circuit and the torque converter clutch (TCC) brake switch signal circuit at the stop lamp switch harness connector. Refer to Using Fused Jumper Wires .
  4. Turn ON the ignition.
  5. Observe the Brake Switch Status on the scan tool.
Does the scan tool display OFF?		 Go to Step 9  Go to Step 6 
6 Test the ignition 3 voltage circuit and the TCC brake switch signal circuit for an open or a short to ground. Refer to Circuit Testing and to Wiring Repairs .
Did you find and correct the condition?		 Go to Step 12  Go to Step 8 
7 Test the TCC brake switch signal circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs .
Did you find and correct the condition?		 Go to Step 12  Go to Step 8 
8 Inspect for poor connections at the harness connector of the electronic brake control module (EBCM). Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs .
Did you find and correct the condition?		 Go to Step 12  Go to Step 10 
9 Inspect for poor connections at the harness connector of the stop lamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs .
Did you find and correct the condition?		 Go to Step 12  Go to Step 11 
10 Replace the EBCM. Refer to Control Module References for replacement, setup and programming.
Did you complete the replacement?		 Go to Step 12  -
11 Replace the stop lamp switch. Refer to Stop Lamp Switch Replacement (Adjustable Pedal) or Stop Lamp Switch Replacement (Non-Adjustable Pedal) .
Did you complete the replacement?		 Go to Step 12  -
12
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals