Conditions for Running the DTC

P0131

• DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
• The Loop Status parameter is Closed.
• The Ignition 1 Signal parameter is between 10-18 volts.
• The Fuel Level Sensor parameter is more than 10 percent.
• The Throttle Position (TP) Indicated Angle parameter is between 3-70 percent.
• DTC P0131 runs continuously when the above conditions are met for 2 seconds.

P0132

• DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
• The Loop Status parameter is Closed.
• The Ignition 1 Signal parameter is between 10-18 volts.
• The Fuel Level Sensor parameter is more than 10 percent.
• The Throttle Position (TP) Sensor parameter is between 0-70 percent.
• DTC P0132 runs continuously when the above conditions are met for 2 seconds.

P0137

• DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
• The Loop Status parameter is Closed.
• The Ignition 1 Signal parameter is between 10-18 volts.
• The Fuel Level Sensor parameter is more than 10 percent.
• The TP Sensor parameter is between 3-70 percent.
• DTC P0137 runs the lean test continuously when the above conditions are met for 2 seconds.

P0138

• DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
• The Loop Status parameter is Closed.
• The Ignition 1 Signal parameter is between 10-18 volts.
• The Fuel Level Sensor parameter is more than 10 percent.
• The TP Sensor parameter is between 3-70 percent.
• DTC P0138 runs the rich test continuously when the above conditions are met for 2 seconds.