Exhaust Popping/Snapping Noise When Vehicle is Hot, at Idle, or Immediately After Vehicle is Shut Off (Replace Muffler Heat Shield) (03-06-05-008D)

Exhaust Popping/Snapping Noise When Vehicle is Hot, at Idle, or Immediately After Vehicle is Shut Off (Replace Muffler Heat Shield)

TECHNICAL SERVICE BULLETIN

Condition

Some customers may comment on a popping/snapping noise from underneath the vehicle at idle or immediately after the vehicle is shut off. Some popping/snapping noise from the exhaust system during cool down is a normal condition.

The noise may be intermittent depending on the outside temperature and or temperature of the exhaust system at the time of testing.

Cause

As the exhaust system warms and cools, the muffler and the muffler heat shield expand and contract at different rates and may cause a popping and/or snapping noise.

Some popping/snapping noise from the exhaust system during cool down is a normal condition. The customer should be made aware that this service procedure is designed to reduce but not eliminate all exhaust system popping and snapping during cool down.

Correction

Follow the service procedure below to correct this condition.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
   CAUTION:

   • In order to avoid being burned, do not service the exhaust system while it is still hot. Service the system when it is cool.
   • Always wear protective goggles and gloves when removing exhaust parts as falling rust and sharp edges could result in serious personal injury.
2. Remove the nuts securing the muffler to the catalytic converter.
3. On 6.0L and 8.1L equipped vehicles only, loosen the exhaust pipe clamp.
IMPORTANT: Do not use oil base lubricants on the rubber exhaust hangers.
4. Apply a soapy solution to the exhaust pipe hanger rods in order to ease the removal of the exhaust hangers.
5. Pry the exhaust hangers free from the exhaust pipe hanger rods.
IMPORTANT: It is not necessary to remove the muffler from the vehicle to replace the muffler heat shield.
6. Reposition the muffler to gain access to the muffler heat shield.
   Fig 1: Muffler Heat Shield

   Courtesy of GENERAL MOTORS CORP.
   NOTE: Use extreme caution not to damage the muffler when removing the heat shield from the muffler.
7. Using an air-powered hack saw blade, or equivalent, cut off the existing muffler heat shield just as the heat shield rises off of the muffler. See the illustration above.
8. Remove the heat shield from the muffler.
9. Hammer flush the remaining heat shield to the muffler.
Fig 2: New Heat Shield
Courtesy of GENERAL MOTORS CORP.
IMPORTANT:
• The new heat shield should not come in contact with the remaining muffler heat shield.
• The new heat shield should not come in contact with the horizontal lock seam on the muffler.
10. Install the new heat shield (see parts list below) onto the muffler as shown above.
Fig 3: Heat Shield Strap
Courtesy of GENERAL MOTORS CORP.
11. Install three straps, P/N 10391259, so that the strap screw head will be located on top of the muffler.

    Tighten:   Tighten the strap screw to 4 N.m (35 lb in).

Fig 4: Strap Screw Head
Courtesy of GENERAL MOTORS CORP.
12. Cut off the excess strap material and bend the strap over the strap screw head as indicated above.
13. Remove the exhaust pipe clamp.
IMPORTANT: ONLY 6.0L and 8.1L equipped vehicles require a new exhaust pipe clamp, P/N 15103174.
14. On 6.0L and 8.1L equipped vehicles only, install a new exhaust pipe clamp, P/N 15103174, on the exhaust pipe.
15. Reposition the muffler in the correct position.
16. Slide the muffler forward into position, aligning the studs with the rear of the catalytic converter.
17. Install the nuts securing the muffler to the catalytic converter, but DO NOT tighten at this time.
18. Apply a soapy solution to the following areas in order to ease the installation of the hangers.
    • The inner diameter of the exhaust pipe hanger
    • The exhaust pipe hanger rod
19. Press the exhaust pipe hangers over the exhaust pipe hanger rods.

    Tighten:  

    • Tighten the muffler nuts by hand until each contacts the metal flange.
    • Tighten the muffler nuts to 45 N.m (33 lb ft).
    • On 6.0L and 8.1L equipped vehicles only, tighten the exhaust clamp to 50 N.m (36 lb ft).

20. Lower the vehicle.

Parts Information

Warranty Information

For vehicles repaired under warranty, use: