LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2003 >> H2 >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel, Gages, And Console >> Repair Instructions >> Instrument Panel (I/P) Carrier Replacement >> Installation Procedure

Installation Procedure

    IMPORTANT: Make sure the ambient light sensor is routed to the top of the I/P.
    Fig 1: Aligning I/P & Routing Electrical Harnesses
    GM815925Courtesy of GENERAL MOTORS CORP.
  1. Align the I/P in the vehicle and route all electrical harnesses through the I/P retainer.
    2. NOTE: Refer to Fastener Notice in Cautions and Notices.
  2. Install the upper and side I/P carrier bolts.

    Tighten:  Tighten the bolts to 50 N.m (37 lb ft).

    3. Fig 2: I/P Carrier Center Support Bracket Nut
    GM832818Courtesy of GENERAL MOTORS CORP.
  3. Install the I/P carrier center support nut.

    Tighten:  Tighten the nut to 9 N.m (80 lb in).

    4. Fig 3: Front Assist Handle
    GM922456Courtesy of GENERAL MOTORS CORP.
  4. Install the windshield garnish moldings. Refer to Garnish Molding Replacement - Windshield Pillar .
  5. Install the upper HVAC air temperature sensors from the HVAC ducts. Refer to Air Temperature Sensor Replacement - Upper Right and Air Temperature Sensor Replacement - Upper Left in HVAC Systems - Automatic.
  6. Install the lower HVAC air temperature sensors from the HVAC ducts. Refer to Air Temperature Sensor Replacement - Lower Left and Air Temperature Sensor Replacement - Lower Right in HVAC Systems - Automatic.
    7. Fig 4: Driver Knee Bolster
    GM816351Courtesy of GENERAL MOTORS CORP.
  7. Install the steering column. Refer to Steering Column Replacement in Steering Wheel and Column.
    8. Fig 5: Knee Bolster Trim Panel
    GM832830Courtesy of GENERAL MOTORS CORP.
  8. Install the drivers knee bolster. Refer to Trim Panel Replacement - Knee Bolster .
    9. Fig 6: I/P Air Bag Module
    GM815846Courtesy of GENERAL MOTORS CORP.
  9. Install the I/P air bag module. Refer to Inflatable Restraint Instrument Panel Module Replacement in SIR.
    10. Fig 7: I/P Compartment
    GM832822Courtesy of GENERAL MOTORS CORP.
  10. Install the I/P storage compartment. Refer to Compartment Replacement - Instrument Panel (I/P) .
    11. Fig 8: Headlamp Switch
    GM815903Courtesy of GENERAL MOTORS CORP.
  11. Install the headlamp switch. Refer to Headlamp Switch Replacement in Lighting Systems.
    12. Fig 9: Rear Wiper Switch
    GM815902Courtesy of GENERAL MOTORS CORP.
  12. Install the rear wiper switch. Refer to Wiper/Washer Switch Replacement - Rear in Wipers/Washer Systems.
    13. Fig 10: Switch Receptacle Screws
    GM815899Courtesy of GENERAL MOTORS CORP.
  13. Install the transfer case control switch module. Refer to Transfer Case Shift Control Module Replacement in Transfer Case - BW 4484.
    14. Fig 11: Traction Control & Air Ride Module Assembly
    GM815914Courtesy of GENERAL MOTORS CORP.
  14. Install the traction control, air ride module to center stack and make electrical connections.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

    15. Fig 12: Identifying Radio
    GM815852Courtesy of GENERAL MOTORS CORP.
  15. Install the radio. Refer to Radio Replacement in Entertainment.
    16. Fig 13: Communication Interface Module & I/P
    GM815865Courtesy of GENERAL MOTORS CORP.
  16. Install the Onstar® module from center stack. Refer to OnStar Button Assembly Replacement in Cellular Communication.
    17. Fig 14: HVAC Control
    GM815858Courtesy of GENERAL MOTORS CORP.
  17. Install the HVAC control. Refer to HVAC Control Module Replacement in HVAC Systems - Automatic.
    18. Fig 15: I/P Upper Trim Pad
    GM832820Courtesy of GENERAL MOTORS CORP.
  18. Install the I/P upper trim pad. Refer to Trim Pad Replacement - Instrument Panel (I/P) Upper .
    19. Fig 16: I/P Cluster Electrical Connections
    GM816329Courtesy of GENERAL MOTORS CORP.
  19. Install the IPC cluster and trim panel. Refer to Instrument Panel Cluster (IPC) Replacement .
    20. Fig 17: Data Link Connector
    GM386625Courtesy of GENERAL MOTORS CORP.
  20. Install the diagnostic connector to the I/P.
  21. Tighten the data link connector screws.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

  22. Connect brake release lever to I/P.

    Tighten:  Tighten the screws to 2 N.m (18 lb in).

    23. Fig 18: I/P Accessory Left Trim Panel
    GM816356Courtesy of GENERAL MOTORS CORP.
  23. Install the left accessory trim panel. Refer to Trim Plate Replacement - Instrument Panel (I/P) Accessory Left .
    24. Fig 19: I/P Accessory Right Trim Panel
    GM816334Courtesy of GENERAL MOTORS CORP.
  24. Install the right accessory trim panel. Refer to Trim Plate Replacement - Instrument Panel (I/P) Accessory Right .
    25. Fig 20: I/P Assist Handle
    GM816332Courtesy of GENERAL MOTORS CORP.
  25. Install the assist handle. Refer to Instrument Panel (I/P) Assist Handle Replacement .
    26. Fig 21: I/P Center Trim Panel
    GM832824Courtesy of GENERAL MOTORS CORP.
  26. Install the I/P center trim panel. Refer to Trim Panel Replacement - Instrument Panel (I/P) Center .
    27. Fig 22: Left & Right I/P Side Trim
    GM816365Courtesy of GENERAL MOTORS CORP.
  27. Align the drivers and passenger side I/P side trim panel and snap into place.
    28. Fig 23: I/P Center Console
    GM816362Courtesy of GENERAL MOTORS CORP.
  28. Install the I/P center console. Refer to Console Replacement .
    29. Fig 24: Installing I/P Insulator
    GM787371Courtesy of GENERAL MOTORS CORP.
  29. Install the passengers insulator. Refer to Insulator Replacement - Instrument Panel (I/P) .
scientia non olet · About LEMON Manuals