LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2021 >> Pilot Special Edition, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Collision/Avoidance >> Blind Spot / Lane Watch System - Testing & Troubleshooting >> Symptom Troubleshooting >> LANEWATCH - LANEWATCH CAMERA IMAGE DOES NOT COME ON (Switches to the black screen) (2016 2017 2018)

LANEWATCH - LANEWATCH CAMERA IMAGE DOES NOT COME ON (Switches to the black screen) (2016 2017 2018)

  1. LaneWatch camera check

    -1. Start the engine.

    - 2. Go into the System Diagnostic Mode, and select the Detail Information and Setting.

    - 3. Select LaneWatch in the Unit Check.

    Is Connection OK?

    YES 

    Go to step 2.

    NO 

    Replace the LaneWatch camera - Go to: LaneWatch Camera Removal and Installation, .

  2. B-CAN check

    -1. Select the Return, then back to Unit Check menu.

    - 2. Select B-CAN in the Unit Check, then start diagnostic.

    Is MICU_ICU changed red?

    YES 

    Go to step 5.

    NO 

    Go to step 3.

  3. Open wire check (LWC CAM V line)

    -1. Turn the vehicle to the OFF (LOCK) mode.

    - 2. Disconnect the following connectors.

    LaneWatch camera 6P connector
    Audio unit or audio-navigation unit connector C (24P)

    - 3. Check for continuity between test points 1 and 2.

    Test condition Vehicle OFF (LOCK) mode
    LaneWatch camera 6P connector: disconnected
    Audio unit or audio-navigation unit connector C (24P): disconnected
    Test point 1 LaneWatch camera 6P connector No. 1
    Test point 2 Audio Unit Connector For Inputs And Outputs [Display Audio Type (8-inch Screen)]
    or audio-navigation unit connector C (24P) No. 20 - Refer to:
    Audio-Navgation Unit Connector for Inputs and Outputs (2016) or
    Audio-Navigation Unit Connector for Inputs and Outputs (2017 2018)
    GHH312527Courtesy of HONDA, U.S.A., INC.

    Is there continuity?

    YES 

    The LWC CAMERA V wire is OK. Go to step 4.

    NO 

    Repair an open in the wire between the LaneWatch camera and the audio unit or the audio-navigation unit.

  4. Open wire check (LWC CAM V GND line)

    -1. Check for continuity between test points 1 and 2.

    Test condition Vehicle OFF (LOCK) mode
    LaneWatch camera 6P connector: disconnected
    Audio unit or audio-navigation unit connector C (24P): disconnected
    Test point 1 LaneWatch camera 6P connector No. 6
    Test point 2 Audio Unit Connector For Inputs And Outputs [Display Audio Type (8-inch Screen)]
    or
    Audio-navigation unit connector C (24P) No. 8 -
    Refer to:
    Audio-Navigation Unit Connector for Inputs and Outputs (2016) or
    Audio-Navigation Unit Connector for Inputs and Outputs (2017 2018)
    GHH312528Courtesy of HONDA, U.S.A., INC.

    Is there continuity?

    YES 

    The LWC CAM V GND wire is OK. Replace the LaneWatch camera - Go to: LaneWatch Camera Removal and Installation .

    NO 

    Repair an open in the wire between the LaneWatch camera and the audio unit or the audio-navigation unit.

  5. Body electrical DTCs check

    -1. Clear the DTC with the HDS.

    - 2. Turn the vehicle to the OFF (LOCK) mode, then the ON mode.

    - 3. Wait for at least 6 seconds.

    - 4. Check for body electrical DTCs with the HDS.

    DTC Description DTC Freeze Frame
         

    Are any DTCs indicated?

    YES 

    Go to The Indicated DTCs Troubleshooting .

    NO 

    Go to step 6.

  6. Open wire check (B CAN-H, B CAN-L line)

    -1. Turn the vehicle to the OFF (LOCK) mode.

    - 2. Disconnect the following connector.

    Under-dash fuse/relay box connector M (10P)
    Audio unit or audio-navigation unit connector C (24P)

    - 3. Check for continuity between test points 1 and 2.

    Test condition OFF mode
    Under-dash fuse/relay box connector M (10P): disconnected
    Audio unit or audio-navigation unit connector C (24P): disconnected
    Test circuit B CAN-H
    Test point 1 Under-dash fuse/relay box connector M (10P) No. 7
    Test point 2 Audio Unit Connector For Inputs And Outputs [Display Audio Type (8-inch Screen)] .
    or
    Audio-navigation unit connector C (24P) No. 13 - Refer to:
    Audio-Navigation Unit Connector for Inputs and Outputs (2016) or
    Audio-Navigation Unit Connector for Inputs and Outputs (2017 2018)
    Test circuit B CAN-L
    Test point 1 Under-dash fuse/relay box connector M (10P) No. 1
    Test point 2 Audio Unit Connector For Inputs And Outputs [Display Audio Type (8-inch Screen)] .
    or
    Audio-navigation unit connector C (24P) No. 3 - Refer to:
    Audio-Navigation Unit Connector for Inputs and Outputs (2016) or
    Audio-Navigation Unit Connector for Inputs and Outputs (2017 2018)

    Is there continuity?

    1. YES 

      The B CAN-H, B CAN-L wires are OK. Check for poor connection or loose terminal at the audio unit or the audio-navigation unit. If the symptom does not go away, replace the audio unit or the audio-navigation unit.

      NO 

      Repair an open in the wire between the under-dash fuse/relay box and the audio unit or the audio-navigation unit.