Battery Charge Control Module Connector For Inputs And Outputs
Battery Charge Control Module Connector for Inputs and Outputs
| Connector Index |
|---|
| Battery Charge Control Module Connector A (36P) |
| Battery Charge Control Module Connector B (40P) |
Battery Charge Control Module Connector A (36P) (female terminals)
Battery Charge Control Module Connector A (36P)
| Terminal number | Terminal name | Description |
|---|---|---|
| 1 | CPL | Detects control pilot line signal |
| 2 | Not used | |
| 3 | Not used | |
| 4 | Not used | |
| 5 | Not used | |
| 6 | Not used | |
| 7 | IGB | Power source for battery charge control module |
| 8 | Not used | |
| 9 | Not used | |
| 10 | WUCM | Sends wake up signal to gauge control module |
| 11 | Not used | |
| 12 | Not used | |
| 13 | Not used | |
| 14 | Not used | |
| 15 | Not used | |
| 16 | IG1 EPP | Power source for battery charge control module |
| 17 | IGC | Power source for battery charge control module |
| 18 | +B CHARGE LID ACT | Power source for battery charge control module (backup) |
| 19 | CPLFS | Detects control pilot line feedback status signal |
| 20 | Not used | |
| 21 | Not used | |
| 22 | Not used | |
| 23 | Not used | |
| 24 | Not used | |
| 25 | Not used | |
| 26 | Not used | |
| 27 | WUCB | Sends wake up signal to battery condition monitor module |
| 28 | Not used | |
| 29 | Not used | |
| 30 | IGC RLY CL- | Drives IGC relay |
| 31 | Not used | |
| 32 | Not used | |
| 33 | Not used | |
| 34 | Not used | |
| 35 | Not used | |
| 36 | GND | Power ground |
Battery Charge Control Module Connector B (40P) (female terminals)
Battery Charge Control Module Connector B (40P)
| Terminal number | Terminal name | Description |
|---|---|---|
| 1 | Not used | |
| 2 | EPP-CAN A_H | Sends and receives EPP-CAN A communication signal (HIGH) |
| 3 | F-CAN D_H | Sends and receives F-CAN D communication signal (HIGH) |
| 4 | F-CAN B_H | Sends and receives F-CAN B communication signal (HIGH) |
| 5 | Not used | |
| 6 | F-CAN A_H | Sends and receives F-CAN A communication signal (HIGH) |
| 7 | Not used | |
| 8 | Not used | |
| 9 | Not used | |
| 10 | Not used | |
| 11 | Not used | |
| 12 | Not used | |
| 13 | Not used | |
| 14 | PXD | Detects charge inlet connector proximity detect signal |
| 15 | TCC1 | Detects charge inlet temperature sensor 1 signal |
| 16 | Not used | |
| 17 | TCC2 | Detects charge inlet temperature sensor 2 signal |
| 18 | Not used | |
| 19 | Not used | |
| 20 | Not used | |
| 21 | Not used | |
| 22 | EPP-CAN A_L | Sends and receives EPP-CAN A communication signal (LOW) |
| 23 | F-CAN D_L | Sends and receives F-CAN D communication signal (LOW) |
| 24 | F-CAN B_L | Sends and receives F-CAN B communication signal (LOW) |
| 25 | Not used | |
| 26 | F-CAN A_L | Sends and receives F-CAN A communication signal (LOW) |
| 27 | Not used | |
| 28 | Not used | |
| 29 | Not used | |
| 30 | Not used | |
| 31 | Not used | |
| 32 | SGT | Sensor ground |
| 33 | Not used | |
| 34 | CHGIND | Drives charge indicator |
| 35 | Not used | |
| 36 | Not used | |
| 37 | Not used | |
| 38 | WUBC | Detects wake up signal from battery condition monitor module |
| 39 | Not used | |
| 40 | WUMC | Detects wake up signal from gauge control module |