DTC P0341 (1.5 L Engine)

DTC P0341  : CMP Sensor A and CKP Sensor Incorrect Phase Detected

NOTE: 

• Before you troubleshoot, review the general troubleshooting information .
• If the DTC P1009 stored at the same time as DTC P0341, troubleshoot DTC P1009 first, then recheck for DTC P0341.

DTC (PGM-FI)

1. Problem verification

   -1. Turn the vehicle to the ON mode.

   -2. Clear the DTC with the HDS.

   -3. Turn the vehicle to the OFF (LOCK) mode, and allow the engine to cool below 104 deg. F (40 deg. C).

   -4. Start the engine, and let it idle without load (in P or N).

   -5. Check for Pending or Confirmed DTCs with the HDS.

   DTC Description	Confirmed DTC	Pending DTC
   P0341 CMP Sensor A and CKP Sensor Incorrect Phase Detected

   Is DTC P0341 indicated?

   YES 

   Go to step 5.

   NO 

   Go to step 2.

2. VTC system check (VTC TEST with the HDS)

   -1. Select the VTC TEST in the INSPECTION MENU with the HDS, then select the IN-VTC.

   VTC TEST

   Is the result OK?

   YES 

   Go to step 3.

   NO 

   Go to step 5.

3. VTC system check (VTC STATUS check with the HDS)

   -1. Test-drive the vehicle at a steady speed between 19-38 mph (30-60 km/h) for 10 minutes.

   -2. Check the parameter (s) below with the HDS.

   Signal	Threshold		Current conditions
   	Values	Unit	Values	Unit
   VTC STATUS	ON

   Do the current condition (s) match the threshold?

   YES 

   Go to step 4.

   NO 

   Do the test-drive again, then recheck the VTC STATUS.

4. VTC system check (OBD status check)

   -1. Monitor the OBD STATUS for DTC P0341 in the DTCs MENU with the HDS.

   DTC Description	OBD STATUS
   P0341 CMP Sensor A and CKP Sensor Incorrect Phase Detected

   Does the HDS indicate FAILED?

   YES 

   Go to step 5.

   NO 

   If the HDS indicates PASSED, intermittent failure, the system is OK at this time. If the on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the on-board snapshot . If the HDS indicates NOT COMPLETED, go to step 3, and recheck.

5. VTC oil control solenoid valve A operation check

   -1. Test VTC oil control solenoid valve A .

   Is the solenoid valve OK?

   YES 

   Go to step 6.

   NO 

   Replace VTC oil control solenoid valve A .

6. Camshaft timing check

   -1. Check the camshaft timing .

   Is the camshaft timing OK?

   YES 

   Go to step 7.

   NO 

   Reset the camshaft timing .

7. Cam chain check

   -1. Check for damage or stretch at the cam chain .

   Is the cam chain damaged or stretched?

   YES 

   Replace the cam chain and the auto-tensioner .

   NO 

   Go to step 8.

8. VTC actuator A check

   -1. Inspect VTC actuator A .

   Is the actuator OK?

   YES 

   Go to step 9.

   NO 

   Replace VTC actuator A .

9. PGM-FI system check (DTC check)

   -1. Turn the vehicle to the ON mode.

   -2. Reset the PCM with the HDS .

   Reset PCM

   -3. Do the CKP pattern clear procedure .

   CRANK (CKP) PATTERN CLEAR

   -4. Do the PCM idle learn procedure .

   -5. Do the CKP pattern learn procedure .

   CRANK PATTERN LEARNING

   -6. Turn the vehicle to the OFF (LOCK) mode, and allow the engine to cool below 104 deg. F (40 deg. C).

   -7. Start the engine, and let it idle without load (in P or N).

   -8. Check for Pending or Confirmed DTCs with the HDS.

   DTC Description	Confirmed DTC	Pending DTC
   P0341 CMP Sensor A and CKP Sensor Incorrect Phase Detected

   Is DTC P0341 indicated?

   YES 

   Check for poor connections or loose terminals at VTC oil control solenoid valve A and the PCM, then go to step 1.

   NO 

   Intermittent failure, the system is OK at this time. If the on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the on-board snapshot .