CVT Transmission Disassembly and Reassembly (CVT): Notes

WARNING: This page is about a different variant/trim than selected.

Image	Description/Tool Number
Courtesy of HONDA, U.S.A., INC.	Driver Handle, 40 mm I.D. 07746-0030100
Courtesy of HONDA, U.S.A., INC.	Bearing Driver Attachment, 30 mm I.D. 07746-0030300
Courtesy of HONDA, U.S.A., INC.	Driver Handle, 15 x 135L 07749-0010000
Courtesy of HONDA, U.S.A., INC.	Bearing Driver Attachment, 62 x 64 mm 07947-6340400

Image	Description/Tool Number
Courtesy of HONDA, U.S.A., INC.	Fuel Sender Wrench 07AAA-S0XA100
Courtesy of HONDA, U.S.A., INC.	Oil Seal Driver Attachment 07GAD-PG40100
Courtesy of HONDA, U.S.A., INC.	Attachment, 78 x 90 mm 07GAD-SD40101

Image	Description/Tool Number
Courtesy of HONDA, U.S.A., INC.	Oil Seal Driver, 65 mm 07JAD-PL9A100
Courtesy of HONDA, U.S.A., INC.	Attachment, 70 mm 07LAD-PW50500
Courtesy of HONDA, U.S.A., INC.	Bearing Driver Attachment, 78 x 80 mm 07NAD-PX40100
Courtesy of HONDA, U.S.A., INC.	Adjustable Bearing Puller, 45-75 mm 07YAC-0010102*

*: 07YAC-0010102 must be used with a commercially available 3/8"-16 slide hammer.

Special Tools Required

Image	Description/Tool Number
Courtesy of HONDA, U.S.A., INC.	Reverse Brake Spring Compressor Set 070AF-RJ2A100
Courtesy of HONDA, U.S.A., INC.	Bearing Driver Attachment, 72 x 75 mm 07746-0010600
Courtesy of HONDA, U.S.A., INC.	Attachment, 22 x 24 mm 07746-001A800
Courtesy of HONDA, U.S.A., INC.	Driver Handle, 40 mm I.D. 07746-0030100
Courtesy of HONDA, U.S.A., INC.	Bearing Driver Attachment, 30 mm I.D. 07746-0030300
Courtesy of HONDA, U.S.A., INC.	Driver Handle, 15 x 135L 07749-0010000
Courtesy of HONDA, U.S.A., INC.	Bearing Driver Attachment, 62 x 64 mm 07947-6340400
Courtesy of HONDA, U.S.A., INC.	Fuel Sender Wrench 07AAA-S0XA100
Courtesy of HONDA, U.S.A., INC.	Oil Seal Driver Attachment 07GAD-PG40100
Courtesy of HONDA, U.S.A., INC.	Attachment, 78 x 90 mm 07GAD-SD40101
Courtesy of HONDA, U.S.A., INC.	Oil Seal Driver, 65 mm 07JAD-PL9A100
Courtesy of HONDA, U.S.A., INC.	Attachment, 70 mm 07LAD-PW50500
Courtesy of HONDA, U.S.A., INC.	Bearing Driver Attachment, 78 x 80 mm 07NAD-PX40100
Courtesy of HONDA, U.S.A., INC.	Adjustable Bearing Puller, 45-75 mm 07YAC-0010102*

*: 07YAC-0010102 must be used with a commercially available 3/8"-16 slide hammer.