LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2014 >> Pilot EX-L, FWD >> Repair and Diagnosis >> Heating, Ventilation & A/C (HVAC) >> HVAC Control Systems >> Heating/Air Conditioning >> DTC Troubleshooting >> DTC B1223 or DTC indicator 1: A Problem in the Rear Blower Motor Circuit

DTC B1223 or DTC indicator 1: A Problem in the Rear Blower Motor Circuit

  1. Clear the DTCs with the HDS.
  2. Turn the ignition switch to LOCK (0) and then back to ON (II).
  3. Do the self-diagnostic function with the HDS (see HOW TO USE THE SELF-DIAGNOSTIC FUNCTION WITH THE HDS  ) or the HVAC control unit (see HOW TO USE THE HVAC CONTROL UNIT SELF-DIAGNOSTIC FUNCTION WITHOUT THE HDS  ).
  4. Check for DTCs.

    Is DTC B1223 or 1 indicated? 

    YES  -Go to step 5.

    NO  -Intermittent failure, check for loose wires or poor connections in the rear blower motor circuit.

  5. Turn the ignition switch to LOCK (0).
  6. Check the No. 5 (RR BLOWER) (30 A) fuse in the auxiliary under-hood fuse/relay box and the No. 36 (10 A) fuse in the under-dash fuse/relay box.

    Are the fuses OK? 

    YES  -Go to step 7.

    NO  -Replace the fuse(s), and recheck. If fuse(s) blow again, check for a short in the No. 5 (RR BLOWER) (30 A) and No. 36 (10 A) fuse(s) circuit.

  7. Connect rear blower motor 2P connector terminal No. 2 to body ground with a jumper wire.
    Fig 1: Identifying Rear Blower Motor 2P Connector Terminal No. 2 Connection With Body Ground Using Jumper Wire
    G08090178Courtesy of AMERICAN HONDA MOTOR CO., INC.
  8. Turn the ignition switch ON (III).

    Does the rear blower motor run at high speed? 

    YES  -Go to step 9.

    NO  -Go to step  24.

  9. Turn the ignition switch to LOCK (0).
  10. Disconnect the jumper wire.
  11. Disconnect the rear power transistor 4P connector.
  12. Check for continuity between rear power transistor 4P connector terminal No. 2 and body ground.
    Fig 2: Checking Continuity Between Rear Power Transistor 4P Connector Terminal No. 2 And Body Ground
    G08090179Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Go to step 13.

    NO  -Check for an open in the wire between the rear power transistor and body ground. If the wire is OK, check for poor ground at G801 (see CONNECTOR TO FUSE/RELAY BOX INDEX ).

  13. Connect rear power transistor 4P connector terminals No. 2 and No. 4 with a jumper wire.
    Fig 3: Identifying Connection Between Rear Power Transistor 4P Connector Terminals No. 2 And 4 Using Jumper Wire
    G08090180Courtesy of AMERICAN HONDA MOTOR CO., INC.
  14. Turn the ignition switch to ON (II).

    Does the rear blower motor run at high speed? 

    YES  -Go to step 15.

    NO  -Repair an open in the ORN wire between the rear power transistor and the rear blower motor.

  15. Turn the ignition switch to LOCK (0).
  16. Disconnect the jumper wire.
  17. Disconnect HVAC control unit connectors A (24P) and B(16P).
  18. Check for continuity between body ground and HVAC control unit connector A (24P) terminal No. 13 and HVAC control unit connector B (16P) terminal No. 11 individually.
    Fig 4: Checking Continuity Between Body Ground And HVAC Control Unit Connector A (24P) Terminal No. 13
    G08090181Courtesy of AMERICAN HONDA MOTOR CO., INC.
    Fig 5: Checking Continuity Between Body Ground And HVAC Control Unit Connector B (16P) Terminal No. 11
    G08090182Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Repair a short to body ground in the wire(s) between the HVAC control unit and the rear power transistor.

    NO  -Go to step 19.

  19. Check for continuity between the following terminals of HVAC control unit connectors A (24P), B (16P) and the rear power transistor 4P connector.

    24P: 4P: 

    No. 13 No. 3

    16P: 4P: 

    No. 11 No. 1

    Fig 6: Checking Continuity Between Terminals Of HVAC Control Unit Connectors A (24P), B (16P) And Rear Power Transistor 4P Connector
    G08090183Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Go to step 20.

    NO  -Repair an open in the wire(s) between the HVAC control unit and the rear power transistor.

  20. Turn the ignition switch to ON (II).
  21. Measure the voltage between body ground and HVAC control unit connector A (24P) terminal No. 13 and HVAC control unit connector B (16P) terminal No. 11 individually.
    Fig 7: Measuring Voltage Between Body Ground And HVAC Control Unit Connector A (24P) Terminal No. 13
    G08090184Courtesy of AMERICAN HONDA MOTOR CO., INC.
    Fig 8: Measuring Voltage Between Body Ground And HVAC Control Unit Connector B (16P) Terminal No. 11
    G08090185Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there any voltage? 

    YES  -Repair a short to power in the wire(s).

    NO  -Go to step 22.

  22. Reconnect HVAC control unit connectors A (24P) and B(16P).
  23. Test the rear power transistor (see REAR POWER TRANSISTOR TEST ).

    Is the rear power transistor OK? 

    YES  -Check for loose wires or poor connections at HVAC control unit connector A (24P) and at the rear power transistor 4P connector. If the connections are good, substitute a known-good HVAC control unit, and recheck. If the symptom/indication goes away, replace the original HVAC control unit (see HVAC CONTROL UNIT REMOVAL/INSTALLATION  ).

    NO  -Replace the rear power transistor (see REAR POWER TRANSISTOR TEST ).

  24. Disconnect the jumper wire.
  25. Disconnect the rear blower motor 2P connector.
  26. Measure the voltage between rear blower motor 2P connector terminal No. 1 and body ground.
    Fig 9: Measuring Voltage Between Rear Blower Motor 2P Connector Terminal No. 1 And Body Ground
    G08090186Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  -Replace the rear blower motor (see REAR BLOWER MOTOR REPLACEMENT ).

    NO  -Go to step 27.

  27. Turn the ignition switch to LOCK (0).
  28. Remove the rear blower motor relay from the dashboard wire harness, and test it (see POWER RELAY TEST ).

    Is the relay OK? 

    YES  -Go to step 29.

    NO  -Replace the rear blower motor relay.

  29. Measure the voltage between rear blower motor relay 5P socket terminal No. 1 and body ground.
    Fig 10: Measuring Voltage Between Rear Blower Motor Relay 5P Socket Terminal No. 1 And Body Ground
    G08090187Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  -Go to step 30.

    NO  -Repair an open in the wire between the No. 5 (RR BLOWER) (30 A) in the auxiliary under-hood fuse/relay box and the rear blower motor relay.

  30. Turn the ignition switch to ON (II).
  31. Measure the voltage between rear blower motor relay 5P socket terminal No. 5 and body ground.
    Fig 11: Measuring Voltage Between Rear Blower Motor Relay 5P Socket Terminal No. 5 And Body Ground
    G08090188Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  -Go to step 32.

    NO  -Repair an open in the wire between the No. 36 (10 A) fuse in the under-dash fuse/relay box and the rear blower motor relay.

  32. Turn the ignition switch to LOCK (0).
  33. Check for continuity between rear blower motor relay 5P socket terminal No. 3 and body ground.
    Fig 12: Checking Continuity Between Rear Blower Motor Relay 5P Socket Terminal No. 3 And Body Ground
    G08090189Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Repair an open in the GRY wire between the rear blower motor relay and the rear blower motor.

    NO  -Check for an open in the wire between the rear blower motor relay and body ground. If the wire is OK, check for poor ground at G801 (see CONNECTOR TO FUSE/RELAY BOX INDEX ).

scientia non olet · About LEMON Manuals