DTC B0072-2B: Short to Another Wire Harness in the Front Passenger's Seat Belt Tensioner (2017)
NOTE:
- Before doing this troubleshooting procedure, find out if the vehicle was in a collision. If so, verify that all the required components were replaced with new components of the correct part number and were properly installed. Refer to: SRS Component Replacement/Inspection After Deployment
- Before doing this troubleshooting procedure, review SRS Precautions and Procedures , General Troubleshooting Information , and 12 Volt Battery Terminal Disconnection and Reconnection .
| DTC Description | DTC |
|---|---|
| B0072-2B Short to another wire harness in the front passenger's seat belt tensioner |
DTC (SRS)
- Problem verification
-1. Clear the DTCs with the HDS.
- 2. Turn the vehicle to the ON mode, then wait for 10 seconds.
- 3. Check for DTCs with the HDS.
DTC Description DTC B0072-2B Short to another wire harness in the front passenger's seat belt tensioner Is DTC B0072-2B indicated?
YES
The failure is duplicated. Go to step 2.
NO
Intermittent failure, the system is OK at this time. Go to Troubleshooting Intermittent Failures . If another DTC is indicated, troubleshoot the DTC.
- DTC check
-1. Check for DTCs with the HDS.
DTC Description DTC B0020-2B Short to another wire harness in the driver's side airbag inflator B0021-2B Short to another wire harness in the left side curtain airbag first inflator B0028-2B Short to another wire harness in the front passenger's airbag inflator B0029-2B Short to another wire harness in the right side curtain airbag first inflator B0070-2B Short to another wire harness in the driver's seat belt tensioner B0072-2B Short to another wire harness in the front passenger's seat belt tensioner Is DTC B0020-2B, B0021-2B, B0028-2B, B0029-2B, or B0070-2B indicated with DTC B0072-2B?
YES
Go to step 3.
NO
Short to another wire in the right side wire harness; replace the faulty harness, then clear the DTC.
- Shorted wire check (RRP lines to another line)
-1. Turn the vehicle to the OFF (LOCK) mode.
- 2. Disconnect the negative cable from the 12 volt battery, then wait at least 3 minutes.
- 3. Disconnect the following connector:
SRS unit connector B (39P) - 4. Check for continuity between test points 1 and 2 of SRS unit connector B (39P) according to table.
Test condition Vehicle OFF (LOCK) mode SRS unit connector B (39P): disconnected DTC SRS unit connector B (39P) - Refer to: SRS Unit Connector for Inputs and Outputs (2017) Test point 1 Test point 2 From terminal To terminal B0020-2B No. 19 No. 5 No. 18 No. 6 B0021-2B No. 19 No. 9 No. 18 No. 10 B0028-2B No. 19 No. 4 No. 18 No. 3 B0029-2B No. 19 No. 8 No. 18 No. 7 DTC SRS unit connector B (39P) - Refer to: SRS Unit Connector for Inputs and Outputs (2017) Test point 1 Test point 2 From terminal To terminal B0070-2B No. 19 No. 20 No. 18 No. 21 Is there continuity?
YES
Short to another wire in the left or right side wire harness; replace the faulty harness, then clear the DTC.
NO
The RRP wires are OK. Faulty SRS unit or poor connection at SRS unit connector B (39P) and the SRS unit. Check the connection; if the connection is OK, check for any authorized service information related to the DTCs or symptoms you are troubleshooting or replace the SRS unit . If the DTC does not clear, replace the left or right side wire harness.