LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2013 >> Fit Base, Automatic Trans >> Repair and Diagnosis >> Engine Performance >> System >> PGM-FI System >> DTC Troubleshooting >> DTC P0351, P0352, P0353, P0354: No. 1 Cylinder Ignition Coil Circuit Malfunction; No. 2 Cylinder Ignition Coil Circuit Malfunction; No. 3 Cylinder Ignition Coil Circuit Malfunction; No. 4 Cylinder Ignition Coil Circuit Malfunction

DTC P0351, P0352, P0353, P0354: No. 1 Cylinder Ignition Coil Circuit Malfunction; No. 2 Cylinder Ignition Coil Circuit Malfunction; No. 3 Cylinder Ignition Coil Circuit Malfunction; No. 4 Cylinder Ignition Coil Circuit Malfunction

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review GENERAL TROUBLESHOOTING INFORMATION .
  1. Turn the ignition switch to ON (II).
  2. Clear the DTC with the HDS.
  3. Start the engine.
  4. Check for Pending or Confirmed DTCs with the HDS.

    Is DTC P0351, P0352, P0353, and/or P0354 indicated? 

    YES:  Go to step  5.

    NO:  Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the ignition coil and the ECM/PCM.

  5. Turn the ignition switch to LOCK (0).
  6. Exchange the ignition coil from the problem cylinder with one from another cylinder (see IGNITION COIL REMOVAL/INSTALLATION ).
  7. Start the engine.
  8. Check for Pending or Confirmed DTCs with the HDS.

    Is an ignition coil DTC indicated at the exchanged cylinder position? 

    YES:  Replace the faulty ignition coil (see IGNITION COIL REMOVAL/INSTALLATION ), then go to step  25.

    NO:  Go to step  9.

  9. Turn the ignition switch to LOCK (0).
  10. Check the No. 33 IGNITION COIL (15 A) fuse in the under-dash fuse/relay box.

    Is the fuse OK? 

    YES:  Go to step  11.

    NO:  Go to step  12.

  11. Open the fuse access panel (A), then test the ignition coil relay (B) in the under-dash fuse/relay box (see REMOVAL AND INSTALLATION ).

    Is the ignition coil relay OK? 

    YES:  Go to step  15.

    NO:  Replace the ignition coil relay, then go to step  25.

    Fig 1: Identifying Fuse Access Panel & Ignition Coil Relay
    G05952894Courtesy of AMERICAN HONDA MOTOR CO., INC.
  12. Open the fuse access panel (A), then remove the ignition coil relay (B) from the under-dash fuse/ relay box.
    Fig 2: Identifying Fuse Access Panel & Ignition Coil Relay
    G05952895Courtesy of AMERICAN HONDA MOTOR CO., INC.
  13. Disconnect all ignition coil 3P connectors.
  14. Check for continuity between No. 1 ignition coil 3P connector terminal No. 3 and body ground.

    Is there continuity? 

    YES:  Repair short in the wire between the ignition coils and the ignition coil relay. Also replace the No. 33 IG COIL (15 A) fuse, then go to step  25.

    NO:  Check the under-dash fuse/relay box, and replace it if needed (see REMOVAL AND INSTALLATION ), then go to step  25.

    Fig 3: Checking Continuity Between No. 1 Ignition Coil 3P Connector Terminal No. 3 & Body Ground
    G05952896Courtesy of AMERICAN HONDA MOTOR CO., INC.
  15. Reinstall the ignition coil relay.
  16. Disconnect the ignition coil 3P connector from the problem cylinder.
  17. Turn the ignition switch to ON (II).
  18. Measure the voltage between ignition coil 3P connector terminal No. 3 of the problem cylinder and body ground (see table below).
    DTC TABLE

    PROBLEM CYLINDER DTC
    No. 1 P0351
    No. 2 P0352
    No. 3 P0353
    No. 4 P0354

    Is there battery voltage? 

    YES:  Go to step  19.

    NO:  Repair open in the wire between the ignition coil and the ignition coil relay, then go to step  25.

    Fig 4: Measuring Voltage Between Ignition Coil 3P Connector Terminal No. 3 & Body Ground
    G05952897Courtesy of AMERICAN HONDA MOTOR CO., INC.
  19. Turn the ignition switch to LOCK (0).
  20. Check for continuity between ignition coil 3P connector terminal No. 2 of the problem cylinder and body ground (see table below).
    DTC TABLE

    PROBLEM CYLINDER DTC
    No. 1 P0351
    No. 2 P0352
    No. 3 P0353
    No. 4 P0354

    Is there continuity? 

    YES:  Go to step  21.

    NO:  Repair open in the wire between the ignition coil and G101; M/T model (see CONNECTOR TO HARNESS INDEX ), A/T model (see CONNECTOR TO HARNESS INDEX ), then go to step  25.

    Fig 5: Checking Continuity Between Ignition Coil 3P Connector Terminal No. 2 & Body Ground
    G05952898Courtesy of AMERICAN HONDA MOTOR CO., INC.
  21. Jump the SCS line with the HDS.
  22. Disconnect ECM/PCM connector C (49P).
  23. Check for continuity between body ground and the appropriate ECM/PCM connector terminal of the problem cylinder (see table below).
    DTC TABLE

    PROBLEM CYLINDER DTC ECM/PCM TERMINAL WIRE COLOR
    No. 1 P0351 C15 WHT
    No. 2 P0352 C16 WHT/GRN
    No. 3 P0353 C17 WHT/BLK
    No. 4 P0354 C18 WHT/BLU

    Is there continuity? 

    YES:  Repair short in the wire between the ECM/PCM and the ignition coil, then go to step  25.

    NO:  Go to step  24.

    Fig 6: Checking Continuity Between Body Ground & ECM/PCM Connector Terminal
    G05952899Courtesy of AMERICAN HONDA MOTOR CO., INC.
  24. Check for continuity between appropriate ignition coil 3P connector terminal No. 1 and the appropriate ECM/PCM connector terminal of the problem cylinder (see table below).
    DTC TABLE

    PROBLEM CYLINDER DTC ECM/PCM TERMINAL WIRE COLOR
    No. 1 P0351 C15 WHT
    No. 2 P0352 C16 WHT/GRN
    No. 3 P0353 C17 WHT/BLK
    No. 4 P0354 C18 WHT/BLU

    Is there continuity? 

    YES:  Go to step  31.

    NO:  Repair open in the wire between the ECM/PCM and the ignition coil, then go to step  25.

    Fig 7: Checking Continuity Between Ignition Coil 3P Connector Terminal No. 1 & ECM/PCM Connector Terminal
    G05952900Courtesy of AMERICAN HONDA MOTOR CO., INC.
  25. Turn the ignition switch to LOCK (0).
  26. Reconnect all connectors.
  27. Turn the ignition switch to ON (II).
  28. Reset the ECM/PCM with the HDS.
  29. Do ECM/PCM IDLE LEARN PROCEDURE .
  30. Check for Pending or Confirmed DTCs with the HDS.

    Is DTC P0351, P0352, P0353, and/or P0354 indicated? 

    YES:  Check for poor connections or loose terminals at the ignition coil and the ECM/PCM, then go to step  1.

    NO:  Troubleshooting is complete. If any other Pending or Confirmed DTCs are indicated, go to the indicated DTC's troubleshooting.

  31. Reconnect all connectors.
  32. Update the ECM/PCM if it does not have the latest software (see ECM/PCM UPDATE  ), or substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ).
  33. Check for Pending or Confirmed DTCs with the HDS.

    Is DTC P0351, P0352, P0353, and/or P0354 indicated? 

    YES:  Check for poor connections or loose terminals at the ignition coil and the ECM/PCM. If the ECM/PCM was updated, substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then recheck. If the ECM/PCM was substituted, go to step  1.

    NO:  If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM (see ECM/PCM REPLACEMENT  ). If any other Pending or Confirmed DTCs are indicated, go to the indicated DTC's troubleshooting.

scientia non olet · About LEMON Manuals