LEMON Manuals: Even more car manuals for everyone
Home >> Geo >> 1993 >> Storm Base, Standard >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> 1.6L 4-CYL - VIN [6] & 1.8L 4-CYL - VIN [8] >> Torque Specifications

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
A/C Compressor Mounting Bolt 30 (40)
Axle Shaft Nut 137 (186)
Ball Joint-To-Lower Control Arm Nut 115 (156)
Camshaft Bearing Cap Bolt (1) (1.6L) 16 (22)
Camshaft Sprocket Bolt 43 (58)
Center Crossmember Bolt 45 (61)
Connecting Rod Nut
1.6L 11 (15) Plus 55 Degrees
1.8L 18 (24) Plus 100 Degrees
Crankshaft Pulley Center Bolt
1.6L 87 (118)
1.8L 108 (147)
Crankshaft Pulley Side Bolts (SOHC) 17 (23)
Cylinder Head Bolt
1.6L (2)
Step 1 29 (39)
Step 2 58 (79)
1.8L (3)
Step 1 29 (39)
Step 2 58 (79)
Engine Mount Bolt
Front Engine Mount Through Bolt 50 (68)
Front Engine Mount-To-Transaxle Bolt 35 (47)
Rear Engine Mount Through Bolt 76 (103)
Rear Engine Mount-To-Transaxle Bolt 38 (51)
Right (Timing Belt Side) Engine Mount
Bracket Mounting Bolt 29 (39)
Through Bolt 50 (68)
Exhaust Manifold Bolt 30 (41)
Flywheel/Drive Plate
A/T 22 (30) plus 55 Degrees
M/T 58 (79)
Intake Manifold Bolt/Nut Upper & Lower Manifold 17 (23)
Main Bearing Cap Bolt
1.6L (4) 44 (60)
1.8L (4) 65 (88)
Oil Cooler Bolt (1.8L) 32 (44)
Oil Pan Support Bracket-To-Cylinder Block Bolt 50 (68)
Oil Pump Relief Valve Plug 27 (37)
Serpentine Belt Idler Bolt 22 (30)
Throttle Body Bolt 17 (23)
Tie Rod Nut 36 (49)
Timing Belt Tensioner Bolt (DOHC) 31 (42)
Timing Belt Tensioner Bolt (SOHC) 37 (50)
Torque Rod Bolt 50 (68)
Torque Rod Bracket-To-Cylinder Block Bolt 28 (38)
Wheel Lug Nut 87 (118)
INCH Lbs. (N.m) 
Camshaft Bearing Cap Bolt (1.8L) (5) 89 (10)
Crankshaft Pulley-To-Pulley Flange Bolt 89 (10)
Oil Pan Bolt/Nut 89 (10)
Oil Pump Cover Bolt 89 (10)
Oil Pump-To-Cylinder Block Bolt 89 (10)
Rear Seal Retainer Bolt 89 (10)
Valve Cover Bolt
1.6L 89 (10)
1.8L 53 (6)
(1) Tighten bolts in sequence to specification. See Figure .
(2) Tighten bolts in sequence to specification. See Figure .
(3) Tighten bolts in sequence to specification. See Figure .
(4) Using proper sequence, tighten bolts in 3 steps to specification. See Figure .
(5) Tighten bolt in sequence to specification. See Figure .