Self Diagnosis

Self-diagnosis process.

Courtesy of HYUNDAI MOTOR AMERICA
NOTE:
- When operating the self-diagnostics, the below fault (self-diagnostics code) will blink at 0.5 seconds interval on the temperature display settings (driver's side only) and the remaining symbols are OFF.

Fault code display

Continuance operation: DTC code.

Courtesy of HYUNDAI MOTOR AMERICA

Continuance operation: DTC code.

Courtesy of HYUNDAI MOTOR AMERICA

STEP operation.

Normal or one fault code is same as a continuance operation.

DTC code.

Courtesy of HYUNDAI MOTOR AMERICA

Display	Fail description	Remarks
0	Normal
11	Interior Temperature Sensor Disconnection (OPEN, INCAR F/B Voltage ≥ 4.9V)
12	Interior Temperature Sensor Short Circuit (SHORT, INCAR F/B Voltage ≤ 0.1V)
13	External Temperature Sensor Disconnection (OPEN, AMBIENT F/B Voltage ≥ 4.9V)
14	External Temperature Sensor Short Circuit (SHORT, AMBIENT F/B Voltage ≤ 0.1V)
17	Evaporator Temperature Sensor Disconnection (OPEN, EVAP F/B Voltage ≥ 4.9V)
18	Evaporator Temperature Sensor Short Circuit (SHORT, EVAP F/B Voltage ≤ 0.1V)
19	Driver Seat Temperature Control Actuator Feedback Disconnection/Short Circuit (OPEN/SHORT) SHORT Range [TEMP F/B Voltage ≤ 0.1V] OPEN Range [TEMP F/B Voltage ≥ 4.9V]
20	Driver Seat Temperature Control Actuator Motor Constraint (Note that if both the target and constraint ranges fall within the MAXCOOL range [0.1V < TEMP FB voltage ≤ 0.5V] and MAX WARM range [4.5V ≤ TEMP FB voltage < 4.9V], the error code 20 is not displayed because there is no longer any constraint. This will prevent MAX WARM and MAX COOL displaying the code 20 due to error margins of the Actuator and FATC.)	f the actuator cannot reach the desired control position in 10 seconds, then it is deemed constrained
21	Driver Seat Mode Actuator Feedback Disconnection/Short Circuit SHORT Range [DR MODE F/B Voltage ≤ 0.1V] OPEN Range [DR MODE F/B Voltage ≥ 4.9V]
22	Driver Seat Mode Actuator Motor Constraint (Note that if both the target and constraint ranges fall within the VENT range [0.1V < DR MODE FB voltage ≤ 0.5V] and DEF range [4.5V ≤ DRMODE FB voltage < 4.9V], the error code 22 is not displayed because there is no longer any constraint. This will prevent VENT and DEF displaying the code 22 due to error margins of the Actuator and FATC.)	f the actuator cannot reach the desired control position in 10 seconds, then it is deemed constrained
24	Auto-defogging senor short circuit (when communication error occurs on sensor side for more than 5 seconds) or (ADS GLASS TEMP ≤ 0.1) or (ADS GLASS TEMP ≥ 4.9).	ADS specification ONLY
25	Internal/External Air Actuator Position Sensor Disconnection/Short Circuit SHORT Range [INTAKE F/B Voltage ≤ 0.1V] OPEN Range [INTAKE F/B Voltage ≥ 4.9V]
26	Internal/External Air Actuator Motor Constraint (Note that if both the target and constraint ranges fall within the FRE range [0.1V < INTAKE FB voltage ≤ 0.5V] REC range [4.5V ≤ INTAKEFB voltage < 4.9V], the error code 26 is not displayed because there is no longer any constraint. This will prevent FRE and REC displaying the code 26 due to error margins of the Actuator and FATC.)	f the actuator cannot reach the desired control position in 10 seconds, then it is deemed constrained
32	Passenger Seat Temperature Control Actuator Feedback Disconnection/Short Circuit (OPEN/SHORT) SHORT Range [TEMP F/B Voltage ≤ 0.1V] OPEN Range [TEMP F/B Voltage ≥ 4.9V]
33	Passenger Seat Temperature Control Actuator Motor Constraint (Note that if both the target and constraint ranges fall within the MAXCOOL range [0.1V < TEMP FB voltage ≤ 0.5V] and MAX WARM range [4.5V ≤ TEMP FB voltage < 4.9V], the error code 20 is not displayed because there is no longer any constraint. This will prevent MAX WARM and MAX COOL displaying the code 33 due to error margins of the Actuator and FATC.)	If the actuator cannot reach the desired control position in 10 seconds, then it is deemed constrained
34	Console temp door motor Disconnection/Short Circuit (OPEN/SHORT) SHORT Range [TEMP F/B Voltage ≤ 0.1V] OPEN Range [TEMP F/B Voltage ≥ 4.9V]
35	Door motor stalling of console temp (The stalling judgement does not display the error code "35" in the control range [1.13V < TEMP F/B Voltage ≤ 1.53V] and the control range [4.5V ≤ TEMP F/B Voltage < 4.9V]. This is to avoid the error code "35" occurrence due to the FATC error).
36	Console ON/OFF door Disconnection/Short Circuit (OPEN/SHORT) SHORT Range [TEMP F/B Voltage ≤ 0.1V] OPEN Range [TEMP F/B Voltage ≥ 4.9V]
37	Rear Temp Door Motor Constraint (Note that if both the target and constraint ranges fall within the MAXCOOL range [0.1V < TEMP FB voltage ≤ 0.5V] and MAX WARM range [4.5V ≤ TEMP FB voltage < 4.9V], the error code 37 is not displayed because there is no longer any constraint. This will prevent MAX WARM and MAX COOL displaying the code 37 due to error margins of the Actuator and FATC.)	f the actuator cannot reach the desired control position in 10 seconds, then it is deemed constrained
38	Console Mode door Disconnection/Short Circuit (OPEN/SHORT) SHORT Range [TEMP F/B Voltage ≤ 0.1V] OPEN Range [TEMP F/B Voltage ≥ 4.9V]
39	Console Mode Door Constraint (Note that if both the target and constraint ranges fall within the VENT [0.1V < MODE FB voltage ≤ 0.5V] and FLOOR [4.5V ≤ MODE FB voltage < 4.9V], the error code 39 is not displayed because there is no longer any constraint. This will prevent VENT and FLOOR displaying the code 39 due to error margins of the Actuator and FATC.)	If the actuator cannot reach the desired control position in 10 seconds, then it is deemed constrained
43	Defog door Disconnection/Short Circuit (OPEN/SHORT) SHORT Range [TEMP F/B Voltage ≤ 0.1V] OPEN Range [TEMP F/B Voltage ≥ 4.9V]
44	Door motor stalling of defog (The stalling judgement does not display the error code "44" in the vent range [1.95V < DEF FB voltage ≤ 2.35V] and the DEF range [4.5V ≤ DEF FB voltage < 4.9V]. This is to avoid the error code "44" occurrence due to the errors of VENT, door of the DEF and the FATC).	If the actuator cannot reach the desired control position in 10 seconds, then it is deemed constrained
45	APT CAN Signal Error
47	RPM CAN SIGNAL Error
48	Vehicle Speed CAN Signal Error
49	Engine coolant temperature CAN Signal Error
61	Open/short circuit range of passenger seat mode door motor [TEMP F/B Voltage ≤ 0.1V] Open circuit range [TEMP F/B Voltage ≥ 4.9V]
62	Mode door motor stalling of passenger seat (The stalling judgement does not display the error code "62" in the control range [0.1V < TEMP F/B Voltage ≤ 0.5V] and the control range [4.5V ≤ TEMP F/B Voltage < 4.9V]. This is to avoid the error code "62" occurrence due to the FATC error.
68	FRONT Photo sensor LH CAN signal - CAN Signal error
69	FRONT Photo sensor RH CAN signal - CAN Signal error
71	ECV defect (If the ECV OPEN or the input current is less than 100 mA, it is judged as Fail.)
72	Communication error between the rear control
73	Communication error between the front control
74	PM SENSOR Fail
81	Open/short circuit range of console temp A door motor [TEMP F/B Voltage ≤ 0.1V] Open circuit range [TEMP F/B Voltage ≥ 4.9V]
82	Door motor stalling of console temp A (The stalling judgement does not display the error code "82" in the control range [1.13V < TEMP F/B Voltage ≤ 1.53V] and the control range [4.5V ≤ TEMP F/B Voltage < 4.9V]. This is to avoid the error code "35" occurrence due to the FATC error.
83	PM SENSOR High temperature operating condition (More than 85°C (135°F))	PM SENSOR specification ONLY

FAIL SAFE

NO	SIGNAL/ITEM	Failure Criteria	Alternative Value in Case of Failure
1	AMB SENSOR	OPEN/SHORT	Fixed at 20°C
2	INCAR SENSOR	OPEN/SHORT	Fixed at 22°C
3	EVA SENSOR	OPEN/SHORT	Fixed at -2°C
4	DR TEMP DOOR POTENTION METER	OPEN/SHORT	For temperature set to 22°C or lower, move to the Cool location and fix it there. For temperature set to 22.5°C or higher, move to the Warm location and fix it there.
5	PS TEMP DOOR POTENTION METER	OPEN/SHORT	For temperature set to 22°C or lower, move to the Cool location and fix it there. For temperature set to 22.5°C or higher, move to the Warm location and fix it there.
6	MODE DOOR POTENTION METER	OPEN/SHORT	Move to and fix the VENT position if VENT Mode is on Fix the DEF position movement if it is not in the "VENT Mode"
7	INTAKE DOOR POTENTION METER	OPEN/SHORT	For FRE selection, move to the FRE location and fix it there. For REC, move to the REC location and fix it there.
8	DEF DOOR POTENTION METER	OPEN/SHORT	Move the and fix the CLOSE position if VENT or B/L mode. Fix the OPEN position if it is not in the "VENT or B/L mode"
9	ECV VehSpdHiVal (Vehicle Speed)	FFh or Signal not received	Take alternative control based on TCU VehSpdKphVal TCU VehSpdHiVal 1FFh & TCU VehSpdKphVal FFh or if signal is not received, it is considered as vehicle speed FAIL. (0 Kph alternative control)
10	TCU VehSpdKphVal (Vehicle speed calculated by TCU)	FFh or Signal not received	Take alternative control based on TCU_VehSpdKphVal ENV_VehSpdHiVal 1FFh & TCU_VehSpdKphVal FFh or if signal is not received, it is considered as vehicle speed FAIL. (0 Kph alternative control)
11	ENG_EngSpdVal (Engine Speed)	Signal not received	Fixed at 650 RPM
12	ENG_EngSpdErrSta (Error-engine speed signal)	01h or Signal not received	Fixed at 650 RPM
13	ENG_EngClntTempVal (Engine Coolant Temperature)	FFh or Signal not received	Fixed at 90°C (Include estimated torque calculation)
14	ENG_AirconPrsrSnsrVal (APT Sensor Output Value)	FFh or Signal not received	Fixed at 0 hPa
15	BCM_SunRoofOpnSta (SUNROOF ON/OFF)	Signal not received	Sunroof interlocking logic not working
16	CONSOLE TEMP DOOR POTENTION METER	OPEN/SHORT	For temperature set to 22°C or lower, move to the Cool location and fix it there. For temperature set to 22.5°C or higher, move to the Warm location and fix it there.
17	CONSOLE ON/OFF DOOR POTENTION METER	OPEN/SHORT	REAR ON: Fixed at ON position REAR OFF: Fixed at OFF position
18	CONSOLE MODE DOOR POTENTION METER	OPEN/SHORT	Move to and fix the VENT position if VENT Mode is on Fix the DEF position movement if it is not in the "VENT Mode"
19	AUTO DEFOG SENSOR	OPEN/SHORT	0% alternative humidity control
20	Photo sensor signal - LH	CAN signal not received	0V
21	Photo sensor signal - LH	CAN signal not received	0V
22	ECV	OPEN (judged only in IGN ON initialization stage)
23	Console Temp Door Potention Meter and Console Temp (A) Door Potention Meter	OPEN/SHORT	For temperature set to 22°C or lower, move to the Cool location and fix it there. For temperature set to 22.5°C or higher, move to the Warm location and fix it there.