Fastener Specifications (Off Vehicle)
WARNING: This page is about a different car, the 2024 Chevrolet Equinox. However, it is still accessible from the selected car via links, so may be relevant.
Single Use Non-Threaded Fasteners/Components
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| 1-2-3-4 Clutch Fluid Passage Seal |
| 3-5-Reverse and 4-5-6 Clutch Fluid Seal Ring |
| 4-5-6 Clutch Dam Retaining Ring |
| Accumulator Bypass Valve Seal |
| Automatic Transmission Fluid Accumulator Pipe Seal |
| Automatic Transmission Fluid Filter |
| Automatic Transmission Fluid Pump Gasket |
| Automatic Transmission Fluid Pump Pressure Plate Seal |
| Automatic Transmission Fluid Pump Seal |
| Control Solenoid Valve Assembly Filter Plate |
| Control Valve Body Cover Wiring Connector Hole Seal |
| Control Valve Body Gasket |
| Input Speed Sensor Assembly Seal |
| Low and Reverse Clutch Fluid Passage Seal |
| Manual Shaft Detent Lever Hub Pin |
| Manual Shift Shaft Pin |
| Park Pawl Actuator Guide Assembly Seal |
| Park Pawl Actuator Guide Pin |
| Torque Converter Housing Gasket |
| Transfer Case Adapter Seal |
| Turbine Shaft Retainer Ring |
Reusable Threaded Fastener Tightening Specifications
| Application | Ref No.* | Quantity | Size | Specification |
|---|---|---|---|---|
| Metric (English) | ||||
| Automatic Transmission Auxiliary Fluid Accumulator Bolt | 377 | 5 | M8 x 30 | 22 N.m (16 lb ft) |
| A/Trans Fluid Pump Bolt to Converter Housing | ||||
|
200 | 8 | M8 x 33 | 10 N.m (89 lb in) |
|
45° | |||
| Automatic Transmission Fluid Pump Cover Bolt (Gen 3) | 308 | 15 | M6 x 18 | 10 N.m (89 lb in) |
| Automatic Transmission Fluid Pump Cover Bolt (Gen 3) | 329 | 19 | M6 x 25 | 10 N.m (89 lb in) |
| Control Solenoid Valve Assembly (w/TCM and Body) to Case Bolt | 4 | 12 | M6 x 97 | 10 N.m (89 lb in) |
| Control Solenoid Valve Assembly (w/TCM and Body) to Case Bolt | 6 | 3 | M5 x 40.5 | 7 N.m (62 lb in) |
| Control Valve Body Assembly (Complete) Bolt | 400 | 1 | M5 x 40.5 | 7 N.m (62 lb in) |
| Control Valve Body to Case Bolt | 9 | 2 | M6 x 53 | 11 N.m (97 lb in) |
| Control Valve Body to Case Bolt | 10 | 9 | M6 x 60 | 11 N.m (97 lb in) |
| Control Valve Body Cover Bolt | 1 | 13 | M6 x 30 | 12 N.m (106 lb in) |
| Drain Plug | 64 | 1 | 1/8" - 27 NPTF | 12 N.m (106 lb in) |
| Fluid Level Hole Plug | 63 | 1 | 1/8" - 27 NPTF | 12 N.m (106 lb in) |
| Fluid Pressure Test Hole Plug | 51 | 1 | 1/8" - 27 NPTF | 12 N.m (106 lb in) |
| Front Differential Carrier Baffle Bolt - Converter Housing | 204 | 2 | M6 x 25 | 12 N.m (106 lb in) |
| Front Differential Carrier Baffle Bolt - Case | 61 | 2 | M6 x 16 | 12 N.m (106 lb in) |
| Input Shaft Support Bolt | 57 | 3 | M6 x 50 | 12 N.m (106 lb in) |
| Input Speed Sensor Bolt | 21 | 1 | M6 x 23 | 9 N.m (80 lb in) |
| Manual Shift Detent Spring Bolt | 17 | 1 | M6 x 16 | 12 N.m (106 lb in) |
| Output Speed Sensor Bolt | 15 | 1 | M6 x 18 | 9 N.m (80 lb in) |
| Torque Converter and Differential Housing Bolt | ||||
|
27 | 15 | M8 x 30 | 10 N.m (89 lb in) |
|
50° | |||
| *Reference number refers to the component callout number in Disassembled Views | ||||