Installation Procedure

Instrument Panel Upper Molding Retainer (2) - Install

CAUTION:

Refer to Fastener Caution .

Instrument Panel Carrier Bolt (1) - Install and tighten [8x] - Fastener Specifications
Connect the electrical connectors.
Instrument Panel Trim Pad - Right Side (1) - Install
Instrument Panel Trim Pad Bolt (1) - Install and tighten [8x] - Fastener Specifications
Instrument Panel Air Outlet Bezel (1) - Install
Instrument Panel Outer Air Outlet Bolt (1) - Install and tighten [4x] - Fastener Specifications
NOTE:
Left side shown, right side similar.

Radio Front Speaker Grille- Right Side (2) - Install
Secure the retaining tabs.
Radio Front Speaker Grille Bolt (1) - Install and tighten - Fastener Specifications
Instrument Panel Trim Plate (2) - Install
Instrument Panel Trim Plate Bolt (1) - Install and tighten [2x] - Fastener Specifications
Connect the electrical connectors.
Radio Control (1) - Install
Radio Control Bolt (1) - Install and tighten [2x] - Fastener Specifications
Radio Control Bolt (1) - Install and tighten [2x] - Fastener Specifications
Instrument Panel Upper Trim Panel Cover (1) - Install
Secure the retaining tabs.
Instrument Panel Bolt Cover (1) - Install [2x]
Secure the retaining tab.
Instrument Panel Lower Trim Panel (2) - Install
Instrument Panel Lower Trim Panel Bolt (1) - Install and tighten [6x] - Fastener Specifications
Connect the electrical connectors.
Instrument Panel Knee Bolster (1) - Install
Instrument Panel Knee Bolster Bolt (2) - Install and tighten [2x] - Fastener Specifications
Instrument Panel Fuse Block Access Hole Cover (1) - Install
Instrument Panel Compartment (1) - Install
Open the instrument panel compartment door.
Instrument Panel Compartment Bolt (1) - Install and tighten [3x] - Fastener Specifications
Instrument Panel Compartment Bolt (1) - Install and tighten [5x] - Fastener Specifications
Front Floor Console (1) - Install
Connect the electrical connectors to the front floor console (1).
Front Floor Console Retainer Bolt (2) - Install and tighten [5x] - Fastener Specifications
Front Floor Console Bolt Access Hole Cover (1) - Install
Tire Repair Sealer and Tire Air Compressor Retainer (1) - Install and hand tighten
Front Floor Console Lower Applique (1) - Install
Front Floor Console Extension Panel (1) - Install
Front Floor Console Retainer Bolt (2) - Install and tighten [5x] - Fastener Specifications
Front Floor Console Bolt Access Hole Cover (1) - Install
Rear Floor Mat (1) - Install
Tire Air Compressor (2) - Install
Tire Repair Sealer and Tire Air Compressor Retainer (1) - Install and hand tighten
Front Floor Console Lower Applique (1) - Install
Front Floor Console Extension Panel (1) - Install
Front Floor Console Extension Bolt (2) - Install and tighten - Fastener Specifications
Front Floor Console Extension Panel Bolt Access Hole Cover (1) - Install
Install the left and right front floor mat (1).
Return the seat to its original position.
Connect the electrical connector.
Instrument Cluster (1) - Install
Instrument Cluster Bolt (1) - Install and tighten [4x] - Fastener Specifications
Connect the electrical connector.
Instrument Panel Extension (1) - Install
NOTE:
Left side shown, right side similar.

Connect the electrical connector.
Windshield Garnish Molding- Left Side and Right Side (1) - Install [2x]
NOTE:
Left side shown, right side similar.

Windshield Pillar Assist Handle Bolt- Left Side and Right Side (2) - Install and tighten [4x] - Fastener Specifications
Windshield Pillar Assist Handle Cover- Left Side and Right Side (1) - Install [4x]
NOTE:
Left side shown, right side similar.

Body Hinge Pillar Garnish Molding- Left Side and Right Side (1) - Install [2x]
Install the weatherstrip as necessary.
NOTE:
Left side shown, right side similar.

Instrument Panel Outer Trim Cover- Left Side and Right Side (1) - Install [2x]