Installation Procedure
Remove the M10-1.5 x 120mm (3) and the M10-1.5 x 45mm (2) bolts.
- Remove the EN-42386 Flywheel Holding Tool (1).
Crankshaft Sprocket (1) @ Crankshaft - Install
Rotate the crankshaft sprocket until the sprocket alignment mark (1) is in the 12 o'clock position.
Timing Chain Tensioner (1) - Install
- Timing Chain Tensioner Bolt (2) - Install and hand tighten
- Remove and DISCARD the tie strap from the actuator.
- NOTE:
The alignment mark on the camshaft position actuator (2) and the alignment mark on the crankshaft sprocket (1) are off-center from the oil pump feed hole gasket on the timing chain tensioner. The alignment marks need to be lined up with one another, but NOT with the oil feed hole.
The camshaft sprocket alignment mark (1) and the crankshaft sprocket alignment mark (2) must be aligned properly.
If the alignment marks on the camshaft position actuator (1) and crankshaft sprocket (2) are difficult to see or line up, an alternate method can be used. Mark the gear tooth directly opposite of the alignment mark on the camshaft position actuator. Mark the gear tooth directly opposite of the alignment mark on the crankshaft sprocket.
The timing chain has 30 links. Place links (1) and (30) on either side of the mark made on the camshaft position actuator and place links (15) and (16) on either side of the mark made on the crankshaft sprocket. This will ensure that the factory alignment marks are in the correct position and that the engine is properly timed.
- NOTE:
- Properly locate the camshaft position actuator (1) onto the locating pin of the camshaft (2).
- The sprocket teeth and timing chain must mesh.
- The camshaft and the crankshaft sprocket alignment marks MUST be aligned properly.
- Do not use the camshaft position solenoid valve again. Install a NEW valve during assembly.
Identify the alignment hole (1) in the rear face of the camshaft position actuator and the locating pin (2) on the front face of the camshaft.
- WARNING:
Refer to Camshaft Position Actuator Removal and Installation Warning .
Install the camshaft position actuator (3) and timing chain (1). Align the hole in the rear face of the camshaft position actuator with the locating pin on the front face of the camshaft. If necessary, rotate the camshaft or crankshaft sprockets (2) in order to align the timing marks. Use care to install the actuator (3) completely onto the front of the camshaft. Position fingers onto the face of the actuator sprocket and push the actuator onto the front of the camshaft. Never push on the reluctor wheel when attempting to install the actuator.
- Position fingers onto the face of the actuator sprocket (2) and push the actuator onto the front of the camshaft.
Position the EN-42386 Flywheel Holding Tool (1) into place.
- Install the M10-1.5 x 120mm (3) and the M10-1.5 x 45mm (2) bolts and tighten to 50 N.m (37 lb-ft).
- CAUTION:
Refer to Torque-to-Yield Fastener Caution
CAUTION:Refer to Component Fastener Tightening Caution .
Camshaft Position Actuator Solenoid Valve (1) - Install NEW and tighten - Fastener Specifications
- NOTE:
It is possible to push the camshaft rearward when installing the camshaft position actuator solenoid valve. Verify that the camshaft lobes are centered in the valve lifter bores after the camshaft position actuator is installed.
Locate a straight edge (1) across the front face of the engine block (2) and inspect for proper installation of the camshaft position actuator and timing chain (3). With the camshaft position actuator properly and completely installed onto the front of camshaft, the timing chain (3) will not protrude beyond the front face of engine block (2).
Inspect the sprockets for proper alignment. The mark on the camshaft position actuator sprocket (1) should be located in the 6 o'clock position and the mark on the crankshaft sprocket (2) should be located in the 12 o'clock position.
Timing Chain Tensioner Bolt (1) - Install and hand tighten
- CAUTION:
Refer to Fastener Caution .
Timing Chain Tensioner Bolt (1) - Tighten [ 2x ] - Fastener Specifications
Remove the EN-46330 Timing Belt Tensioner Retaining Pin (1) from the timing chain tensioner (2).
Oil Pump (1) - Install
Oil Pump Bolt (1) - Install and hand tighten [ 4x ]
- Oil Pump Bolt (1) - Tighten in sequence [ 4x ] - Fastener Specifications
- NOTE:
- Install and align the front cover within 10 minutes of applying the sealer.
- Ensure proper use of room temperature vulcanizing (RTV) sealant. Use of Room Temperature Vulcanizing (RTV) and Anaerobic Sealant
Apply a 3 mm (0.118 in) bead of RTV sealant on the engine front cover (1). Adhesives, Fluids, Lubricants, and Sealers
- Apply a 5 mm (0.197 in) bead of RTV sealant on the engine front cover (2). Adhesives, Fluids, Lubricants, and Sealers
Engine Front Cover (2) - Install
- Engine Front Cover Bolt (1, 3) - Install and hand tighten [ 10x ]
- Engine Front Cover Bolt (1, 3) - Tighten in sequence [ 10x ] - Fastener Specifications
- NOTE:
If the engine front cover is reused, the crankshaft front oil seal (3) must be replaced.
If the engine front cover is reused, perform the following steps:
- For proper orientation, note the installation direction of the crankshaft front oil seal (3). The crankshaft front oil seal is a reverse-lip design. Install with "THIS SIDE OUT" displayed as shown.
- Do NOT lubricate the crankshaft front oil seal sealing surface.
- Install the crankshaft front oil seal (3) with "THIS SIDE OUT" facing away from the engine.
- Install the NEW crankshaft front oil seal (3) to the EN-51091 Crankshaft Front Oil Seal Installer (2).
- Install the EN-41478-A Crankshaft Front Oil Seal Installer (1) and the EN-51091 Crankshaft Front Oil Seal Installer (2) into the crankshaft.
- Rotate the EN-51091 Crankshaft Front Oil Seal Installer (2) clockwise until the NEW crankshaft front oil seal (3) enters the engine front cover and seats into the bottom of the engine front cover.
- Remove the EN-41478-A Crankshaft Front Oil Seal Installer (1) and the EN-51091 Crankshaft Front Oil Seal Installer (2) from the crankshaft and engine front cover.
- Inspect the crankshaft front oil seal (3) for proper installation. The crankshaft front oil seal should be installed evenly and completely into the engine front cover.
NOTE: Water Pump Gasket (2) - Install NEW [ 2x ]
- Water Pump (1) - Install
If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:
- Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
- Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
- Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
- Ensure there are no gaps in the thread locking adhesive once applied to the component.
- Water Pump Housing Bolt (1) - Install and hand tighten [ 6x ]
- Water Pump Housing Bolt (1) - Tighten in sequence [ 6x ] - Fastener Specifications
Engine Coolant Temperature Sensor Electrical Connector (1) - Connect
Radiator Inlet Hose (3) @ Water Pump - Install
- Engine Coolant Air Bleed Hose (2) @ Water Pump - Install
- Hose Clamp (1) - Engage [ 2x ] - Hose Clamp Replacement Guidelines - Spring Type
Radiator Outlet Hose (2) @ Water Pump - Install
- Radiator Outlet Hose Clamp (1) - Engage - Hose Clamp Replacement Guidelines - Spring Type
Heater Water Auxiliary Pump Hose (3) @ Water Pump - Install
- Heater Inlet Hose (2) @ Water Pump - Install
- Hose Clamp (1) - Engage [ 2x ] - Hose Clamp Replacement Guidelines - Spring Type
Air Conditioning Compressor (1) - Install
Air Conditioning Compressor Bolt (1) - Loosely install
- Air Conditioning Compressor Stud (3) - Install and tighten - Fastener Specifications
- Air Conditioning Compressor Bolt (1) - Tighten - Fastener Specifications
- Air Conditioning Compressor Nut (2) - Install and tighten - Fastener Specifications
Generator (1) - Install
Generator Bolt (1) - Install and tighten [ 2x ] - Fastener Specifications
Engine Cooler Fan (1) @ Engine Radiator - Install
Engine Coolant Fan Bracket Bolt (1) - Install and tighten [ 2x ] - Fastener Specifications
Transmission Fluid Cooler Pipe Clip (1) - Secure
Transmission Fluid Cooler Pipe Clip (2) - Install [ 2x ]
- Transmission Fluid Cooler Pipe Bolt (1) - Install and tighten - Fastener Specifications
Engine Oil Cooler Hose (1) @ Engine Radiator - Install [ 2x ]
- Engine Oil Cooler Pipe Bracket Bolt (3) - Install and tighten - Fastener Specifications
- Engine Oil Cooler Retainer (2) - Install [ 2x ]
Engine Oil Cooler Hose Clip (1) - Secure
Position the wiring harness. (3)
- Electrical Connector (1) - Connect
- Wiring Harness Retainer (2) - Install [ 2x ]
Position the wiring harness. (2)
- Electrical Connector (3) - Connect
- Wiring Harness Retainer (1) - Install [ 2x ]
Radiator Inlet Hose (3) @ Engine Radiator - Install
- Radiator Inlet Hose Clamp (1) - Engage - Hose Clamp Replacement Guidelines - Spring Type
- Radiator Inlet Hose Clip (2) - Install
Radiator Surge Tank Outlet Hose (3) - Move into position
- Radiator Surge Tank Outlet Hose Clip (2) - Install [ 2x ]
Apply a 3 mm (0.118 in) bead of RTV sealant on the oil pan (1). Adhesives, Fluids, Lubricants, and Sealers
- Apply a 5 mm (0.197 in) bead of RTV sealant on the oil pan (2). Adhesives, Fluids, Lubricants, and Sealers
Oil Pan High Pressure Port Seal (2) - Install NEW [ 2x ]
- Oil Pan Front Seal (3) - Install NEW
Oil Pan (1) - Install
- Oil Pan Bolt (2, 3) - Install and hand tighten [ 16x ]
- Oil Pan Bolt (2, 3) - Tighten in sequence [ 16x ] - Fastener Specifications
Electrical Connector (1) - Connect
Crankshaft Balancer (1) - Loosely install
Install the EN-41478-A Crankshaft Front Oil Seal Installer (3) and the EN-41665-A Crankshaft Balancer and Sprocket Installer (2) to the crankshaft.
- Using the EN-41665-A Crankshaft Balancer and Sprocket Installer (2) properly seat the crankshaft balancer (1).
- Remove the EN-41478-A Crankshaft Front Oil Seal Installer (3) and the EN-41665-A Crankshaft Balancer and Sprocket Installer (2).
- CAUTION:
Refer to Torque-to-Yield Fastener Caution
Crankshaft Balancer Bolt (1) - Install NEW and tighten - Fastener Specifications
Engine Wiring Harness (3) - Install
- Engine Wiring Harness Retainer (2) - Install
- Engine Wiring Harness Ground Stud (1) - Install and tighten [ 2x ] - Ground Repair
Install and tighten the transmission fluid auxiliary cooler pipe bracket nut (1). Fastener Specifications
- NOTE:
Components removed in graphic to better illustrate service parts.
Transmission Fluid Cooler Pipe Clip Bracket (2) @ Oil Pan - Install
- Transmission Fluid Cooler Pipe Clip Bolt (1) @ Oil Pan - Install and tighten - Fastener Specifications
Electrical Connector @ Knock Sensor (4) - Connect
Oil Filter (1) - Install and tighten - Fastener Specifications
Transmission Bolt (1) - Install and tighten [ 2x ] - Fastener Specifications
Engine Oil Cooler Gasket (2) - Install NEW
- Engine Oil Cooler Hose (1) @ Oil Pan - Install
Engine Oil Cooler Adapter Bolt (1) - Install and tighten [ 2x ] - Fastener Specifications
Electrical Connector (1) @ Engine Oil Pressure Sensor - Connect
- Wiring Harness Retainer (2) @ Engine Oil Cooler Hose - Install
Engine Oil Pressure Sensor Sleeve (1) - Install
Engine Oil Cooler Hose Bracket Nut (1) - Install and tighten - Fastener Specifications
Lubricate the oil level indicator seal (2) with clean engine oil. Adhesives, Fluids, Lubricants, and Sealers
- Oil Level Indicator Seal (2) - Install NEW
- Oil Level Indicator Tube (1) @ Oil Pan - Install
Connect the wiring harness connectors (3) and retainers as needed.
- Engine Wiring Harness Retainer (1) @ Oil Level Indicator Tube (2) - Connect
Remove the M10-1.5 x 120mm (3) and the M10-1.5 x 45mm (2) bolts.
- Remove the EN-42386 Flywheel Holding Tool (2)
Torque Converter Cover- Right Side (2) - Install
- Torque Converter Cover Bolt- Right Side (1) - Install and tighten - Fastener Specifications
Torque Converter Cover- Left Side (2) - Install
- Torque Converter Cover Bolt- Left Side (1) - Install and tighten - Fastener Specifications
Starter (1) - Install
Electrical Connector (3) - Connect
- Protective Sleeve (4) - Install
- Starter Solenoid Cable (1) - Install
- Starter Solenoid Cable Nut (2) - Install and tighten - Fastener Specifications
Starter Bolt (1) - Install and tighten [ 2x ] - Fastener Specifications
Starter Solenoid Cable (2) - Install
- Battery Negative Cable Ground Bolt (1) - Install and tighten - Fastener Specifications
Starter Heat Shield (2) - Install
- Starter Heat Shield Bolt (1) - Install and tighten - Fastener Specifications
Starter Heat Shield Bolt (1) - Install and tighten [ 2x ] - Fastener Specifications
- NOTE:
The front axle may have to be maneuvered to install it into the vehicle.
Front Axle (1) - Install
- Front Axle Vent Hose - Connect
Front Differential Carrier Bolt (1) - Install and tighten - Fastener Specifications
Front Differential Carrier Bolt (2) - Install
- Front Differential Carrier Bracket Nut (1) - Install and tighten - Fastener Specifications
Drivetrain and Front Suspension Frame Front Crossmember (1) - Install
Drivetrain and Front Suspension Frame Reinforcement Bolt (2) - Install [ 4x ]
- Using the EN-45059-A Angle Meter, install and tighten the 4 drivetrain and front suspension frame reinforcement nuts (1). Fastener Specifications
- CAUTION:
Refer to Torque-to-Yield Fastener Caution
Front Differential Carrier Bolt (2) - Install NEW
- Front Differential Carrier Nut (1) - Install
- Using the EN-45059-A Angle Meter, tighten the front differential carrier nut (1). Fastener Specifications
- NOTE:
Some components not shown for graphic clarity.
Install the heater coolant pump and heater water auxiliary pump bracket (2) as assembly.
- Heater Water Auxiliary Pump Bolt (1) - Install and tighten - Fastener Specifications
- Electrical Connector @ Heater Coolant Pump (2) - Connect
Connect the front drive axle actuator electrical connector (1).
- Install the harness and secure the two harness retainers (2).
If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:
- Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
- Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
- Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
- Ensure there are no gaps in the thread locking adhesive once applied to the component.
- Front Axle Propeller Shaft (1) - Install
- Align the reference marks made between the front axle propeller shaft (1) and the front differential drive pinion gear yoke.
- Front Axle Propeller Shaft Washer (3) - Install [ 3x ]
- Install the 6 front axle propeller shaft bolts (2) and tighten in a crisscross pattern. Fastener Specifications
- NOTE:
Support the front stabilizer shaft.
- Front Stabilizer Shaft (3) - Install
- Front Stabilizer Shaft Clamp (2) - Install [ 2x ]
- If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:
- Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
- Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
- Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
- Ensure there are no gaps in the thread locking adhesive once applied to the component.
- Front Stabilizer Shaft Bolt (1) - Install and tighten [ 4x ] - Fastener Specifications
- NOTE:
Prior to installing the front shock absorber, you MUST apply anti-corrosion wax to the frame shock tower.
Apply anti-corrosion wax to the frame shock tower. Anti-Corrosion Treatment and Repair
- Front Shock Absorber (1) - Install
- NOTE:
Using a jack stand support the lower control arm to prevent over-articulation of the front lower control arm ball joint.
Front Shock Absorber Bolt (1) - Install and tighten [ 2x ] - Fastener Specifications
Front Shock Absorber Nut (1) - Install and tighten [ 3x ] - Fastener Specifications
Install the chassis wiring harness bracket (1) to the frame shock tower.
- Front Wheelhouse Liner- Left Side - Install - Front Wheelhouse Liner Replacement
Remove any buildup from the front differential carrier output shaft lead in chamfer (1) using an abrasive pad and wipe clean with a shop cloth.
Front Wheel Drive Shaft Seal (2) - Install NEW
- Front Wheel Drive Shaft Retaining Ring (1) - Install NEW
- Apply a thin coating of grease to the splines of the front wheel drive half shaft and front differential carrier output shaft. Adhesives, Fluids, Lubricants, and Sealers
- NOTE:
Some components not shown for graphic clarity.
Install the front wheel drive half shaft (1) into the wheel hub.
- Install the front wheel drive half shaft (1) into the front axle.
- Ensure that the left front wheel drive half shaft (1) is fully seated in front differential carrier by pulling on the inner joint.
- Support the steering knuckle with a suitable jack stand.
Front Upper Control Arm Ball Stud Nut (1) - Install and tighten - Fastener Specifications
- Remove jack stand.
Front Stabilizer Shaft Link @ Front Lower Control Arm - Install
- Front Stabilizer Shaft Link Nut (1) - Install and tighten - Fastener Specifications
Steering Linkage Outer Tie Rod - Install
- Steering Linkage Outer Tie Rod Nut (1) - Install and tighten - Fastener Specifications
Install the front wheel speed sensor wiring harness bracket (2).
- Front Wheel Speed Sensor Bracket Bolt (1) - Install and tighten - Fastener Specifications
Front Wheel Speed Sensor (2) - Install
- Front Wheel Speed Sensor Bolt (1) - Install and tighten - Fastener Specifications
- Front Wheel Speed Sensor Bracket (4) - Install
- Front Wheel Speed Sensor Bracket Bolt (3) - Install and tighten - Fastener Specifications
If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:
- Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
- Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
- Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
- Ensure there are no gaps in the thread locking adhesive once applied to the component.
- Front Brake Caliper (1) - Install
- Front Brake Caliper Bolt (2) - Install and tighten [ 2x ] - Fastener Specifications
Front Brake Hose Bracket Bolt (1) - Install and tighten - Fastener Specifications
- NOTE:
Only the left front wheel is equipped with the front disc brake pad wear sensor.
Front Disc Brake Pad Wear Sensor (1) @ Front Brake Caliper - Install
Remove any buildup from the front differential carrier output shaft lead in chamfer (1) using an abrasive pad and wipe clean with a shop cloth.
Front Wheel Drive Shaft Seal (2) - Install NEW
- Front Wheel Drive Shaft Retaining Ring (1) - Install NEW
- Apply a thin coating of grease to the splines of the front wheel drive half shaft and front differential carrier output shaft. Adhesives, Fluids, Lubricants, and Sealers
- NOTE:
Some components not shown for graphic clarity.
Install the front wheel drive half shaft (1) into the wheel hub.
- Install the front wheel drive half shaft (1) into the front axle.
- Ensure that the right front wheel drive half shaft (1) is fully seated in front differential carrier by pulling on the inner joint.
- Support the steering knuckle with a suitable jack stand.
Front Upper Control Arm Ball Stud Nut (1) - Install and tighten - Fastener Specifications
- Remove jack stand.
Front Stabilizer Shaft Link @ Lower Control Arm - Install
- Front Stabilizer Shaft Link Nut (1) - Install and tighten - Fastener Specifications
Steering Linkage Outer Tie Rod - Install
- Steering Linkage Outer Tie Rod Nut (1) - Install and tighten - Fastener Specifications
Install the front wheel speed sensor wiring harness bracket (2).
- Front Wheel Speed Sensor Bracket Bolt (1) - Install and tighten - Fastener Specifications
Front Wheel Speed Sensor (2) - Install
- Front Wheel Speed Sensor Bolt (1) - Install and tighten - Fastener Specifications
- Front Wheel Speed Sensor Bracket (4) - Install
- Front Wheel Speed Sensor Bracket Bolt (3) - Install and tighten - Fastener Specifications
If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:
- Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
- Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
- Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
- Ensure there are no gaps in the thread locking adhesive once applied to the component.
- Front Brake Caliper (1) - Install
- Front Brake Caliper Bolt (2) - Install and tighten [ 2x ] - Fastener Specifications
Front Brake Hose Bracket Bolt (1) - Install and tighten - Fastener Specifications
- Have an assistant apply the brakes.
- CAUTION:
Refer to Torque-to-Yield Fastener Caution
Front Wheel Drive Shaft Nut (1) - Install NEW and tighten - Fastener Specifications
- CAUTION:
Refer to Torque-to-Yield Fastener Caution
Front Wheel Drive Shaft Nut (1) - Install NEW and tighten - Fastener Specifications
Front Differential Carrier Oil Filler Plug (1) - Remove
- Inspect the gear lubricant level, it should be 16-22 mm (0.6-0.9 in) below the plug opening.
- If the level is low, add gear lubricant until the level is 16-22 mm (0.6-0.9 in) below the plug opening. Use the appropriate axle lubricant: Adhesives, Fluids, Lubricants, and Sealers
- Front Differential Carrier Oil Filler Plug (1) - Install and tighten - Fastener Specifications
Oil Level Indicator Tube Bolt (1) - Install and tighten - Fastener Specifications
Engine Wiring Harness Fuse Block Bracket (3) - Install
- Retaining Tab (1) - Engage
- Engine Wiring Harness Fuse Block Bracket Bolt (2) - Tighten [ 2x ] - Fastener Specifications
Electrical Connector (1) - Install [ 4x ]
Engine Wiring Harness Junction Block (3) - Install
- Retaining Tab (1) - Engage [ 4x ]
- Engine Wiring Harness Junction Block Bolt (2) - Tighten [ 4x ] - Fastener Specifications
Starter Solenoid Cable (4) - Install
- Battery Positive Cable Nut (3) - Install and tighten - Fastener Specifications
- Engine Wiring Harness Junction Block Cover (2) - Install
- Retaining Tab (1) - Engage [ 2x ]
Starter Solenoid Cable (2) - Install
- Battery Positive Cable Nut (1) - Install and tighten - Fastener Specifications
- Electrical Connector (3) - Connect
- NOTE:
The OEM replacement stretchy accessory drive auxiliary belt (1) is packaged with a disposable installation tool and installation instructions.
Install the accessory drive auxiliary belt (1) following the instructions included with the accessory drive auxiliary belt.
- Inspect the accessory drive auxiliary belt (1) for proper installation and alignment.
Rotate the crankshaft balancer (1) an additional 360 degrees to ensure proper accessory drive auxiliary belt installation.
Position the accessory drive primary belt (4) on the belt idler pulley (2), fan and water pump pulley (3) and generator (1).
Install the EN-51767-2 Stretchy Belt Installer (1) onto the crankshaft balancer.
Position the accessory drive primary belt (2) on the crankshaft balancer.
- Slowly rotate the crankshaft balancer in a clockwise direction until the accessory drive primary belt (2) fully seats on the crankshaft balancer.
- Remove the EN-51767-2 Stretchy Belt Installer (1) from the crankshaft balancer.
Inspect the accessory drive primary belt (1) for proper installation and alignment.
Rotate the crankshaft balancer (1) and additional 360 degrees to ensure proper accessory drive primary belt installation.
Air Cleaner Outlet Duct (3) - Install
- Air Cleaner Outlet Duct Clamp (2) - Tighten [ 2x ] - Fastener Specifications
- Positive Crankcase Ventilation Fresh Air Tube (1) - Connect - Plastic Collar Quick Connect Fitting Service
Air Cleaner Outlet Duct Bracket Bolt (1) - Install and tighten - Fastener Specifications
- Install engine wiring harness to air cleaner outlet duct bracket.
Underbody Skid Shield (3) - Install
- Underbody Splash Shield Bolt (2) - Install and tighten [ 2x ] - Fastener Specifications
Underbody Splash Shield (1) - Install
Underbody Splash Shield Bolt (1) - Install and tighten [ 4x ]
- Underbody Splash Shield Bolt (2) - Install and tighten [ 4x ] - Fastener Specifications
- Install both front tire and wheel assemblies. Tire and Wheel Removal and Installation (Aluminum Wheel)
- Lower the vehicle.
- Fill the engine oil to the proper level with NEW engine oil.
Install the oil level indicator. (1)
- Connect the battery negative cable. Battery Negative Cable Disconnection and Connection (KL9)
- Fill the cooling system. Cooling System Draining and Filling (GE 47716 L84, L87) , or Cooling System Draining and Filling (Static L84, L87) .
- Start the engine and check for coolant leaks.
- Check for oil leaks.
Never push on the reluctor wheel when attempting to install the actuator.