LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2021 >> Yukon AT4 >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel And Console Trim - Diagnostic Information And Procedures >> Diagnostic Information and Procedures >> Cooler Box Malfunction >> Circuit/System Testing

Circuit/System Testing

Test 1

    NOTE:

    Ignition OFF and all vehicle systems OFF and allow the components of the K175 Front Floor Console Compartment Cooler to warm or cool to room temperature prior to performing electrical diagnostics

  2. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the K175 Front Floor Console Compartment Cooler. It may take up to 2 min for all vehicle systems to power down.
  3. Test for less than 10 Ω between the ground circuit terminal 2 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  4. Ignition ON.
  5. Verify a test lamp illuminates between the B+ circuit terminal 1 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF, remove the test lamp.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF, remove the test lamp.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Connect the K175 Front Floor Console Compartment Cooler and replace the fuse.
    4. Ignition ON, verify the fuse does not open when connecting or working the K175 Front Floor Console Compartment Cooler.
      • If the fuse opens, replace the K175 Front Floor Console Compartment Cooler.
      • Go to next step: If the fuse is OK
    5. All OK
    • Go to next step: If the test lamp illuminates 
  6. Ignition OFF and all vehicle systems OFF, connect the harness connector at the K175 Front Floor Console Compartment Cooler and disconnect the S145 Beverage Cooler Switch. It may take up to 2 min for all vehicle systems to power down.
  7. Test for less than 10 Ω between the ground circuit terminal 1 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  8. Test for 11 - 12 V between the signal circuit terminal 4 and ground.
    • If less than 11 V 
    1. Ignition OFF, disconnect the harness connector at the K175 Front Floor Console Compartment Cooler.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K175 Front Floor Console Compartment Cooler.
    • If greater than 11 V 
    1. Ignition OFF, disconnect the harness connector at the K175 Front Floor Console Compartment Cooler, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K175 Front Floor Console Compartment Cooler.
    • Go to next step: If between 11 - 12 V 
  9. Replace the K175 Front Floor Console Compartment Cooler.

Test 2

    NOTE:

    Ignition OFF and all vehicle systems OFF and allow the components of the K175 Front Floor Console Compartment Cooler to warm or cool to room temperature prior to performing electrical diagnostics

  2. Ignition OFF and all vehicle systems OFF, disconnect the S145 Beverage Cooler Switch.
  3. Test for less than 1 V between the indicator control circuit terminal 4 and ground.
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • Go to next step: If less than 1 V 
  4. Test for infinite resistance between the indicator control circuit terminal 4 and ground.
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • Go to next step: If infinite resistance 
  5. Disconnect the harness connector at the K175 Front Floor Console Compartment Cooler.
  6. Test for less than 2 Ω in the control circuit end to end.
    • If 2 Ω or greater 

      Repair the open/high resistance in the circuit.

    • Go to next step: If less than 2 Ω 
  7. Connect the S145 Center Console Compartment Cooler Switch.
  8. Install 3 A fused jumper harness between K175 Front Floor Console Compartment Cooler harness connector terminal 4 and ground
  9. Ignition ON, verify indicator illuminates.
    • If the indicator illuminates 

      Replace the K175 Front Floor Console Compartment Cooler.

    • Go to next step: If the indicator does not illuminate 
  10. Test for less than 1 V between the indicator control circuit terminal 5 and ground.
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • Go to next step: If less than 1 V 
  11. Test for infinite resistance between the indicator control circuit terminal 5 and ground.
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • Go to next step: If infinite resistance 
  12. Disconnect the harness connector at the K175 Front Floor Console Compartment Cooler.
  13. Test for less than 2 Ω in the control circuit end to end.
    • If 2 Ω or greater 

      Repair the open/high resistance in the circuit.

    • Go to next step: If less than 2 Ω 
  14. Connect the S145 Center Console Compartment Cooler Switch.
  15. Install 3 A fused jumper harness between K175 Front Floor Console Compartment Cooler harness connector terminal 5 and ground
  16. Ignition ON, verify indicator illuminates.
    • If the indicator illuminates 

      Replace the K175 Front Floor Console Compartment Cooler.

    • Go to next step: If the indicator does not illuminate 
  17. Replace the S145 Beverage Cooler Switch.
scientia non olet · About LEMON Manuals