LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2018 >> Acadia Denali, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 409 (Frame And Underbody) >> Repair Instructions >> Rear Suspension Cradle Replacement (FWD) >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2017 GMC Acadia. However, it is still accessible from the selected car via links, so may be relevant.
  1. Raise and support the vehicle. Lifting and Jacking the Vehicle
  2. Remove Exhaust Muffler Assembly Exhaust Muffler Replacement (LGX)Exhaust Muffler Replacement (LCV)
  3. Remove the rear wheels. Tire and Wheel Removal and Installation
    4. Fig 1: Electrical Connector
    GM4298051Courtesy of GENERAL MOTORS COMPANY
  4. Disconnect Electrical Connector (1)
  5. Release the retainers.(2)
  6. Using mechanics wire, support the rear suspension knuckle assembly.
    7. Fig 2: Rear Suspension Lower Control Arm
    GM4285062Courtesy of GENERAL MOTORS COMPANY
  7. Separate Rear Suspension Lower Control Arm (1) @Rear Knuckle Lower Control Arm Replacement
    8. Fig 3: Rear Suspension Lower Trailing Link
    GM4287288Courtesy of GENERAL MOTORS COMPANY
  8. Separate Rear Suspension Lower Trailing Link (1) @Rear Knuckle Rear Suspension Lower Trailing Link Replacement
    9. Fig 4: Rear Suspension Upper Lateral Link
    GM4286809Courtesy of GENERAL MOTORS COMPANY
  9. Separate Rear Suspension Upper Lateral Link@Rear Knuckle Rear Suspension Upper Lateral Link Replacement
    10. Fig 5: Rear Suspension Upper Trailing Link
    GM4286933Courtesy of GENERAL MOTORS COMPANY
  10. Separate Rear Suspension Upper Trailing Link (1) @Rear Knuckle Rear Suspension Upper Trailing Link Replacement
    11. Fig 6: Rear Suspension Adjust Link
    GM4286554Courtesy of GENERAL MOTORS COMPANY
  11. Separate Rear Suspension Adjust Link (1) @Rear Knuckle Adjust Link Replacement
    12. Fig 7: Wheel Speed Sensor Harness Retainers And Rear Suspension Cradle
    GM4298257Courtesy of GENERAL MOTORS COMPANY
  12. Release the wheel speed sensor harness retainers from the rear suspension cradle and adjust link. (1)
    13. Fig 8: Stabilizer Shaft Link
    GM4194201Courtesy of GENERAL MOTORS COMPANY
  13. Separate Stabilizer Shaft Link (1) @Stabilizer Shaft Stabilizer Shaft Link Replacement
    14. Fig 9: Rear Suspension Cradle Bolt And Rear Cradle Mount Bolt Bracket Bolt
    GM4298330Courtesy of GENERAL MOTORS COMPANY
  14. Using the EN-39580  Support Stand support the rear suspension cradle.
  15. Remove Rear Suspension Cradle Bolt (1) and DISCARD
  16. Remove Rear Cradle Mount Bolt Bracket Bolt (2)
    17. Fig 10: Rear Wheel Speed Sensor Connectors And Chassis Harness Retainers
    GM4298478Courtesy of GENERAL MOTORS COMPANY
  17. Carefully lower the rear suspension cradle to access the rear wheel speed sensor connectors (1) and the chassis harness retainers (2).
  18. Disconnect Electrical Connector (1)
  19. Release the retainers. (2)
    20. Fig 11: Rear Suspension Cradle
    GM4298422Courtesy of GENERAL MOTORS COMPANY
  20. Remove Rear Suspension Cradle (1)
  21. If replacing the rear suspension cradle, transfer parts as necessary.
scientia non olet · About LEMON Manuals