LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2018 >> Acadia Denali, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 350 (Rear Drive Axle) >> Diagnostic Information and Procedures >> DTC C1260-C1267: Power Transfer Unit Clutch Position Sensor >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2017 GMC Acadia. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF and all vehicle systems OFF, disconnect the X1 harness connector at the M115 Power Transfer Unit Shift Actuator. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the low reference circuit terminal 3 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF, disconnect the X1 harness connector at the K47 Rear Differential Clutch Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K47 Rear Differential Clutch Control Module.
    • If less than 10 Ω 
  3. Ignition ON/Vehicle In Service Mode.
  4. Test for 4.8-5.2 V between the 5 V reference circuit terminal 2 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the X1 harness connector at the K47 Rear Differential Clutch Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K47 Rear Differential Clutch Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the X1 harness connector at the K47 Rear Differential Clutch Control Module, ignition ON/Vehicle In Service Mode.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K47 Rear Differential Clutch Control Module.
    • If between 4.8-5.2 V 
  5. Ignition OFF, disconnect the X1 harness connector at the K47 Rear Differential Clutch Control Module, ignition ON/Vehicle In Service Mode.
  6. Test for less than 1 V between the M115 harness connector terminal 1 and ground.
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • If less than 1 V 
  7. Ignition OFF.
  8. Test for infinite resistance between M115 harness connector terminal 1 and ground.
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • If Infinite resistance 
  9. Test for less than 2 Ω between M115 Power Transfer Unit Shift Actuator - terminal 1 and K47 Rear Differential Clutch Control Module - terminal 14 end to end.
    • If 2 Ω or greater 

      Repair the open/high resistance in the circuit.

    • If less than 2 Ω 
  10. Test or replace the M115 Power Transfer Unit Shift Actuator.
  11. Operate the vehicle under the conditions for setting the DTC, the DTC should not set.
    • If the DTC sets 

      Replace the K47 Rear Differential Clutch Control Module.

scientia non olet · About LEMON Manuals