LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2018 >> Acadia Denali, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 334 (Lighting System) >> Diagnostic Information and Procedures >> Turn Signal Lamps and/or Indicators Malfunction >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2017 GMC Acadia. However, it is still accessible from the selected car via links, so may be relevant.

Turn Signal/Multifunction Switch Malfunction

  1. Ignition OFF, scan tool disconnected, all doors closed, all accessories OFF, open and close drivers door, disconnect the harness connector at the S78 Turn Signal/Multifunction Switch. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 3 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify the scan tool Left Turn Signal Switch parameter is Inactive.
    • If not Inactive 
    1. Ignition OFF, disconnect the X3 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit terminal 1 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If Inactive 
  5. Install a 3 A fused jumper wire between the signal circuit terminal 1 and ground.
  6. Verify the scan tool Left Turn Signal Switch parameter is Active.
    • If not Active 
    1. Ignition OFF, disconnect the X3 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 1 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If Active 
  7. Verify the scan tool Right Turn Signal Switch parameter is Inactive.
    • If not Inactive 
    1. Ignition OFF, disconnect the X3 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit terminal 2 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If Inactive 
  8. Install a 3 A fused jumper wire between the signal circuit terminal 2 and ground.
  9. Verify the scan tool Right Turn Signal Switch parameter is Active.
    • If not Active 
    1. Ignition OFF, disconnect the X3 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 2 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If Active 
  10. Test or replace the S78 Turn Signal/Multifunction Switch.

Turn Signal Lamps Malfunction

  1. Ignition OFF, exterior lamps OFF, disconnect the harness connector at the appropriate turn signal lamp. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 5 Ω between the appropriate ground circuit terminal listed below and ground.
    • E4N Park/Turn Signal Lamp - Left terminal 3 (with T3W)
    • E4P Park/Turn Signal Lamp - Right terminal 3 (with T3W)
    • E4LF Turn Signal Lamp - Left Front terminal 3 (with T7E)
    • E4RF Turn Signal Lamp - Right Front terminal 3 (with T7E)
    • E5S Tail/Stop and Turn Signal Lamp - Left socket terminal
    • E5T Tail/Stop and Turn Signal Lamp - Right socket terminal
    • If 5 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 5 Ω 
  3. Connect a test lamp between the appropriate control circuit terminal listed below and ground, ignition ON.
    • E4N Park/Turn Signal Lamp - Left terminal 1 (with T3W)
    • E4P Park/Turn Signal Lamp - Right terminal 1 (with T3W)
    • E4LF Turn Signal Lamp - Left Front terminal 1 (with T7E)
    • E4RF Turn Signal Lamp - Right Front terminal 1 (with T7E)
    • E5S Tail/Stop and Turn Signal Lamp - Left socket terminal
    • E5T Tail/Stop and Turn Signal Lamp - Right socket terminal
  4. Verify the test lamp turns ON and OFF when commanding the appropriate Turn Signal Lamp ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the appropriate harness connector listed below at the K9 Body Control Module.
      • X4 left rear turn signal
      • X4 right front turn signals
      • X5 left front turn signals
      • X5 right rear turn signal
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the appropriate harness connector listed below at the K9 Body Control Module, ignition ON.
      • X4 left rear turn signal
      • X4 right front turn signals
      • X5 left front turn signals
      • X5 right rear turn signal
    2. Test for less than 1 V between the control circuit terminal and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  5. Test or replace the turn signal lamp.
scientia non olet · About LEMON Manuals