LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2018 >> Acadia Denali, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 271 (Lighting System - DTC B0655 To DTC B3890) >> Diagnostic Information and Procedures >> DTC B3415: Front Axle Sensor Supply >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2017 Cadillac ATS. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF, disconnect the harness connector at the appropriate B152L Suspension Position Sensor, ignition ON.
  2. Verify a test lamp illuminates between the low reference circuit terminal 2 and B+.
    • If the test lamp does not illuminate 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K26 Headlamp Control Module.
    • If the test lamp illuminates 
  3. Ignition ON.
  4. Test for 4.8-5.2 V between the 5 V reference circuit terminal 1 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K26 Headlamp Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module, ignition ON.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K26 Headlamp Control Module.
    • If between 4.8-5.2 V 
  5. Verify the appropriate scan tool Suspension Position Sensor parameter is less than 1 V.
    • If 1 V or greater 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 3 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K26 Headlamp Control Module.
    • If less than 1 V 
  6. Install a 3 A fused jumper wire between the 5 V reference circuit terminal 1 and the signal circuit terminal 3.
  7. Engine RUNNING, verify the appropriate scan tool Suspension Position Sensor parameter is greater than 4.8 V.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K26 Headlamp Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K26 Headlamp Control Module.
    • If 4.8 V or greater 
  8. Test or replace the appropriate B152L Suspension Position Sensor.
scientia non olet · About LEMON Manuals