LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2018 >> Acadia Denali, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 198 (Manual Transmission - TREMEC 6-Speed (M3L Mg9)) >> Diagnostic Information and Procedures >> DTC P18C6 or P18C7: Gear Position Sensor >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2017 Cadillac ATS. However, it is still accessible from the selected car via links, so may be relevant.
WARNING:

Refer to Hot Exhaust System Warning .

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the B227 Gear Position Sensor. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the low reference circuit terminal 4 and ground.
    • If 10 Ω or greater 
    1. Disconnect the X3 harness connector at the K20 Engine Control Module.
    2. Test for less than 2 Ω in the circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Test for 4.8-5.2 V between the 5 V reference circuit terminal 1 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the X3 harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the X3 harness connector at the K20 Engine Control Module, Ignition ON.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K20 Engine Control Module.
    • If between 4.8-5.2 V 
  5. Verify the scan tool Gate Select Position Sensor parameter duty cycle is greater than 99%.
    • If 99% or less 
    1. Ignition OFF, disconnect the X2 harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit 2 terminal 2 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, test or replace the K20 Engine Control Module.
    • If greater than 99% 
  6. Install a 3 A fused jumper wire between the signal circuit 2 terminal 2 and ground.
  7. Verify the scan tool Gate Select Position Sensor parameter duty cycle is less than 1%.
    • If 1% or greater 
    1. Ignition OFF, remove the jumper wire, disconnect the X2 harness connector at the K20 Engine Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit 2 terminal 2 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the signal circuit 2 end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, test or replace the K20 Engine Control Module.
    • If less than 1% 
  8. Replace the B227 Gear Position Sensor.
scientia non olet · About LEMON Manuals