LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2017 >> Acadia SL >> Repair and Diagnosis >> External Pages >> Different car >> Section 43 (Automatic Transmission - 8L45 (M5N M5T) Or 8L90 (M5U) - Repair Instructions - On Vehicle) >> Repair Instructions - On Vehicle >> Transmission Replacement (M5N with LGX Engine) >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2016 Cadillac ATS. However, it is still accessible from the selected car via links, so may be relevant.
  1. Raise and suitably support the vehicle. Lifting and Jacking the Vehicle (Base)Lifting and Jacking the Vehicle (V-Series) .
  2. Two-Piece Propeller Shaft Replacement (LTG, LGX, LCV) »Remove
  3. {If equipped} Front Axle Propeller Shaft Replacement (LGX, LTG) »Remove
    4. Fig 1: Transmission Range Selector Lever Cable
    GM4032383Courtesy of GENERAL MOTORS COMPANY
  4. Disconnect the transmission range selector lever cable terminal (1) from the transmission manual shift lever pin (6).
  5. Slide the retainer (4) forward to release the transmission range selector lever cable (5) from the bracket.
    6. Fig 2: Transmission Fluid Cooler Pipes
    GM4083607Courtesy of GENERAL MOTORS COMPANY
  6. Place an oil drain pan under the transmission fluid cooler pipes (1).
  7. Remove the transmission fluid cooler inlet and outlet pipes (1) from the transmission, and position aside, or remove from the vehicle as necessary. Transmission Fluid Cooler Inlet and Outlet Pipe Replacement (LGX With RWD, Without V03)Transmission Fluid Cooler Inlet and Outlet Pipe Replacement (LGX With AWD, Without V03)Transmission Fluid Cooler Inlet and Outlet Pipe Replacement (LGX With RWD, With V03) .
  8. Plug the open fluid ports to prevent fluid loss and contamination.
  9. Starter Replacement (LGX) »Remove
  10. Transmission Converter Cover Replacement (Rear Wheel Drive) Transmission Converter Cover Replacement (All Wheel Drive) »Remove
    11. Fig 3: Transmission Close Out Plug
    GM4084382Courtesy of GENERAL MOTORS COMPANY
  11. Remove the transmission close out plug (1).
  12. Mark the torque converter to flexplate orientation to ensure proper realignment.
    13. Fig 4: Torque Converter Bolts
    GM4084885Courtesy of GENERAL MOTORS COMPANY
  13. Repeat the following steps for all torque converter bolts (1):
    1. Rotate the harmonic balancer center bolt clockwise ONLY, in order to align the torque converter bolt with the starter opening.
    2. Remove and Discard the torque converter bolt.
    14. Fig 5: Catalytic Converter Brace Bracket
    GM4084937Courtesy of GENERAL MOTORS COMPANY
  14. Remove the catalytic converter brace bracket (2) from the transmission.
  15. Support the transmission with a suitable transmission jack.
    16. Fig 6: Lower Transmission Bolts
    GM4085785Courtesy of GENERAL MOTORS COMPANY
  16. Remove the lower transmission to engine bolts (1, 2, 3, 4, 5, 6).
  17. Support the transmission with a suitable transmission jack.
  18. Transmission Support Replacement (Automatic RWD)Transmission Support Replacement (Automatic AWD)Transmission Support Replacement (Manual) »Remove
  19. Tilt the transmission downward just enough to gain access to the upper transmission fasteners.
    20. Fig 7: Transmission Vent Hose Retainers
    GM4085926Courtesy of GENERAL MOTORS COMPANY
  20. Disconnect the transmission vent hose retainers (1).
  21. Disconnect the electrical wiring harness retainers from the transmission to engine fasteners and from the transmission case.
    22. Fig 8: Transmission Bolts
    GM4085970Courtesy of GENERAL MOTORS COMPANY
  22. Remove the transmission to engine bolts (1, 2, 3, 4, 5).
  23. Pull the transmission straight back.
  24. Install the J-21366  strap onto the transmission bell housing to retain the torque converter.
  25. Remove the transmission from the vehicle.
  26. Transfer components as necessary.
  27. Flush and flow test the transmission cooler and transmission pipes. Transmission Fluid Cooler Flushing and Flow Test (8L90)
scientia non olet · About LEMON Manuals