LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2006 >> Sierra 1500 HD, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 10 (Engine Mechanical - 8.1L) >> Repair Instructions >> Off-Vehicle Repair Instructions >> Cylinder Head Assemble >> Valve Installation

Valve Installation

WARNING: This page is about a different variant/trim than selected.
    Fig 1: View Of Valve Stems & Components
    GM1310011Courtesy of GENERAL MOTORS CORP.
    CAUTION: Refer to Safety Glasses Caution in Cautions and Notices.
    CAUTION: Compressed valve springs have high tension against the valve spring compressor. Valve springs that are not properly compressed by or released from the valve spring compressor can be ejected from the valve spring compressor with intense force. Use care when compressing or releasing the valve spring with the valve spring compressor and when removing or installing the valve stem keys. Failing to use care may cause personal injury.
  1. Lubricate the valve stems (232) with clean engine oil.
  2. Insert the valves into their proper locations.
  3. Install the necessary valve spring shims onto the cylinder head, if applicable.
  4. Lubricate the rotators (216) with clean engine oil.
  5. Install the rotators over the guide and on top of the cylinder head or valve spring shims, if applicable.
    6. Fig 2: Valve Oil Seals Using J 43105
    GM1310013Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: When installing valve stem oil seals onto the valve guides, be careful not to tear the seal lip.
    IMPORTANT: When installing valve seals, J 43105  must be used to achieve correct installation. See Special Tools . Failure to use J 43105  may cause excessive oil consumption. See Special Tools .
  6. Lubricate the valve stem seal and the outside diameter of the valve guide with clean engine oil.
  7. Install the valve stem oil seals (217) over the valve tip and onto the valve guides using J 43105  (1). See Special Tools . Tap the valve stem seal onto the valve guide until the J 43105  fully seats the seal. See Special Tools .
    8. Fig 3: View Of Valve Stems & Components
    GM1310011Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: When installing valve springs, the small end of the valve spring must be installed up.
  8. Install the valve springs (218).
  9. Install the valve spring caps (219).
    10. Fig 4: Compressing Valve Springs Using J 8062
    GM196664Courtesy of GENERAL MOTORS CORP.
  10. Use the J 8062  in order to compress the valve spring. Compress the spring enough to clearly see the valve stem key grooves of the valve.
  11. Install the valve stem keys.
    • Use grease to hold the keys in place.
    • Ensure that the keys seat properly in the upper groove of the valve stem.
  12. Release and remove the J 8062  .
  13. Lightly tap the end of the valve stem with a plastic-faced hammer to seat the keys.
    14. Fig 5: View Of ECT Sensor
    GM1198701Courtesy of GENERAL MOTORS CORP.
  14. Apply sealant GM P/N 12346004, (Canadian P/N 10953480), or equivalent to the threads of the engine coolant temperature (ECT) sensor.
    15. NOTE: Refer to Fastener Notice in Cautions and Notices.
  15. Install the ECT sensor into the right cylinder head.

    Tighten:  Tighten the ECT sensor to 50 N.m (37 lb ft).

  16. Install the ECT sensor bracket and bolt.

    Tighten:  Tighten the ECT sensor bracket bolt to 50 N.m (37 lb ft).

    17. Fig 6: View Of Cylinder Head Coolant Hole Plug
    GM635678Courtesy of GENERAL MOTORS CORP.
  17. Apply sealant GM P/N 12346004, (Canadian P/N 10953480), or equivalent to the threads of the cylinder head coolant hole plug.
  18. Install the cylinder head coolant hole plug into the left cylinder head.

    Tighten:  Tighten the cylinder head coolant hole plug to 50 N.m (37 lb ft).

scientia non olet · About LEMON Manuals