LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2006 >> Sierra 1500 HD, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Engine Controls - 6.6L - Introduction (2 Of 2)) >> Repair Instructions >> Fuel Pressure Regulator Replacement >> Removal Procedure

Removal Procedure

WARNING: This page is about a different variant/trim than selected.
  1. Remove the air intake pipe. Refer to Air Intake Pipe Replacement .
  2. Disconnect the air conditioning (A/C) compressor clutch electrical connector.
  3. Disconnect the A/C cut out switch electrical connector.
  4. Remove the A/C compressor bolts.
    Fig 1: View Of A/C Compressor & Bolts
    GM652573Courtesy of GENERAL MOTORS CORP.
  5. Remove the generator. Refer to Generator Replacement (4.8L, 5.3L, and 6.0L Engines) or Generator Replacement (6.6L (LLY) Engine) or Generator Replacement (8.1L Engine) .
  6. Reposition the A/C compressor (with the hoses attached) to the right side of the engine compartment.
  7. Disconnect the main engine electrical harness connectors. Lift up on the latches (1) in order to disconnect the connectors.
    Fig 2: View Of Main Engine Electrical Harness Connector Latches & Harness Clip
    GM1409327Courtesy of GENERAL MOTORS CORP.
  8. Open the harness clip (2).
  9. Remove the main engine electrical harness connectors.
    10. Fig 3: View Of Main Engine Electrical Harness Connector Bolts
    GM1334916Courtesy of GENERAL MOTORS CORP.
  10. Remove the main engine harness electrical connector bolts.
  11. Remove the main connectors from the bracket.
    12. Fig 4: View Of Engine Coolant Temperature Sensor And Electrical Connector
    GM1335413Courtesy of GENERAL MOTORS CORP.
  12. Disconnect the engine coolant temperature (ECT) sensor electrical connector.
  13. Remove the water outlet tube. Refer to Water Outlet Tube Replacement (6.6L (LLY) Engine) .
    14. Fig 5: View Of Fuel Temperature Sensor Electrical Connector
    GM1335528Courtesy of GENERAL MOTORS CORP.
  14. Disconnect the fuel temperature sensor electrical connector.
    15. Fig 6: Disconnecting Fuel Pressure Regulator Electrical Connector
    GM786996Courtesy of GENERAL MOTORS CORP.
  15. Disconnect the fuel pressure regulator electrical connector (1).
    16. Fig 7: View Of Oil Level Sensor Electrical Harness Connector
    GM1335526Courtesy of GENERAL MOTORS CORP.
  16. Disconnect the oil level sensor harness electrical connector.
    17. Fig 8: View Of Fuel Hose Connections
    GM1335595Courtesy of GENERAL MOTORS CORP.
  17. Reposition the distribution block hose clamps.
  18. Remove the distribution block hoses from the distribution block.
  19. Clean the fuel pressure regulator and high pressure injection pump thoroughly with solvent, such as GM P/N 12377981 (Canadian P/N 10953463) or equivalent.
  20. Using compressed air, thoroughly blow dry the regulator and pump.
  21. Remove the 3 fuel pressure regulator screws (1) using a T25 TORX®.
    Fig 9: Removing Fuel Pressure Regulator Screws
    GM901300Courtesy of GENERAL MOTORS CORP.
  22. Remove the fuel pressure regulator (1).
    Fig 10: Removing Fuel Pressure Regulator
    GM901301Courtesy of GENERAL MOTORS CORP.
  23. If dirt or debris is found in the bore or seating surfaces of the fuel injection pump, perform the following:
    • Place a clean rag over the bore on order to collect the excess fuel.
    • Bump the engine over in order to flush any debris out of the regulator bore.
scientia non olet · About LEMON Manuals