LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2006 >> Sierra 1500 HD, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Engine Controls - 6.6L - Introduction (2 Of 2)) >> Repair Instructions >> Fuel Injector Feed Pipes Replacement - Left >> Removal Procedure

Removal Procedure

WARNING: This page is about a different variant/trim than selected.
  1. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement .
  2. Drain the cooling system. Refer to Draining and Filling Cooling System (w/RPO HP2) or Draining and Filling Cooling System (w/o RPO HP2) .
  3. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure (Single Battery) or Battery Negative Cable Disconnect/Connect Procedure (Auxiliary Battery) .
    4. IMPORTANT: After removing the charged air cooler duct, cover the turbocharger opening with tape in order to prevent entry of objects.
    IMPORTANT: Do not use a screwdriver or other tool to pry the hose loose. The hose can be torn or damaged. Loosen the hose by twisting.
  4. Loosen the charged air cooler inlet duct connector to turbocharger clamp (1).
  5. Remove the charged air cooler inlet duct connector (4) from the turbocharger.
    Fig 1: View Of Turbocharger Clamp & Charged Air Cooler Inlet Duct Connector
    GM1334380Courtesy of GENERAL MOTORS CORP.
  6. Remove the battery cable to generator nut.
  7. If equipped, remove the battery cable to auxiliary generator nut.
  8. Remove the battery cable harness clip from the bracket.
  9. Remove the battery cable junction block bolt (1) from the power steering pump.
    Fig 2: View Of Battery Cable Junction Block Bolt At Power Steering Pump Bracket
    GM1409332Courtesy of GENERAL MOTORS CORP.
  10. Move and secure the battery cables out of the way.
  11. Disconnect the fuel lines. Refer to Quick Connect Fitting(s) Service (Metal Collar) .
  12. Remove the fuel line bracket nut.
    Fig 3: View Of Fuel Line Bracket & Nut
    GM1378748Courtesy of GENERAL MOTORS CORP.
  13. Remove the fuel line bracket from the stud.
  14. Disconnect the main engine electrical harness connectors. Lift up on the latches (1) in order to disconnect the connectors.
    Fig 4: View Of Main Engine Electrical Harness Connector Latches & Harness Clip
    GM1409327Courtesy of GENERAL MOTORS CORP.
  15. Open the harness clip (2).
  16. Remove the main engine electrical harness connectors.
  17. Remove the engine harness main electrical connectors bolts.
    Fig 5: View Of Main Engine Electrical Harness Connector Bolts
    GM1334916Courtesy of GENERAL MOTORS CORP.
  18. Disconnect the barometric sensor electrical connector.
  19. Remove the engine harness main connector bracket bolts.
    Fig 6: View Of Main Electrical Connector Harness Bracket & Bolts
    GM1334948Courtesy of GENERAL MOTORS CORP.
  20. Remove the water outlet tube. Refer to Water Outlet Tube Replacement (6.6L (LLY) Engine) .
  21. Remove the auxiliary generator, if equipped. Refer to Generator Replacement - Auxiliary (6.6L (LLY) Engine) .
  22. Disconnect the glow plug control module electrical connectors (1, 2).
    Fig 7: Disconnecting Glow Plug Control Module Electrical Connectors
    GM1653265Courtesy of GENERAL MOTORS CORP.
  23. Remove the positive crankcase ventilation (PCV) hose/pipe. Refer to Crankcase Ventilation Hoses/Pipes Replacement .
  24. Prior to removing the fuel injector pipes, use compressed air to blow any debris from between the injector line and fittings. Wipe the fittings clean of debris.
  25. Spray lithium grease, GM P/N 12346293 or equivalent, between the fuel injector line and fittings to assist in containing any debris during removal.
    26. NOTE: DO NOT use compressed air to clean debris from the fuel injector inlet after the fuel line is removed. Using compressed air can allow debris to enter the fuel injector inlet and damage the fuel injector.
    Fig 8: View Of Left Fuel Injector Pipes
    GM1335608Courtesy of GENERAL MOTORS CORP.
  26. Remove the left fuel injector pipes.
scientia non olet · About LEMON Manuals