LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2006 >> Sierra 1500 HD, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 894 (Engine Controls And Fuel - 4.3L - Introduction (2 Of 2)) >> Repair Instructions >> Fuel Hose/Pipes Replacement - Chassis (Extended Cab - w/8 Ft Bed) >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2007 GMC Sierra and 2007 Chevrolet Silverado. However, it is still accessible from the selected car via links, so may be relevant.
IMPORTANT: Clean all fuel and evaporative emission (EVAP) lines connections and surrounding areas prior to disconnecting the lines in order to avoid possible fuel and/or EVAP system contamination.
    Fig 1: View Of Fuel Feed Pipe
    GM1876017Courtesy of GENERAL MOTORS CORP.
  1. Relieve the fuel system pressure. Refer to the Fuel Pressure Relief (With CH 48027)  or Fuel Pressure Relief (Without CH 48027) .
  2. Disconnect the engine evaporative emission (EVAP) line quick connect fitting (2) from the chassis EVAP line. Refer to Plastic Collar Quick Connect Fitting Service .
  3. Disconnect the fuel feed line (1) quick connect fitting from the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .
  4. Cap the fuel rail and EVAP pipes.
  5. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  6. Unbolt and reposition the front propeller shaft, if required. Refer to Front Propeller Shaft Replacement .
    7. Fig 2: View Of Fuel/Evaporative Emission Pipe & Bracket
    GM1701047Courtesy of GENERAL MOTORS CORP.
  7. Remove the fuel pipe bracket nut from the bellhousing stud.
    8. Fig 3: Fuel Hose/Pipe Clip At Bracket On Transfer Case
    GM1855293Courtesy of GENERAL MOTORS CORP.
  8. Remove the fuel line clip (1) from the bracket on the automatic transmission.
  9. If equipped with 4-wheel drive (4WD), remove the fuel hose/pipe clip from the bracket on the transfer case.
    10. Fig 4: EVAP Canister Vent Solenoid Clip & EVAP Canister Vent Solenoid Pipe Clip
    GM1855687Courtesy of GENERAL MOTORS CORP.
  10. Remove the EVAP canister vent solenoid clip (1) from the chassis EVAP line and secure out of the way.
  11. Remove the EVAP canister vent solenoid pipe clip (2) from the chassis EVAP line.
    12. Fig 5: Fuel Feed Lines
    GM1855299Courtesy of GENERAL MOTORS CORP.
  12. If equipped with 2-wheel drive (2WD) perform the following steps, disconnect the fuel tank fuel feed line quick connect fitting from the chassis line. Refer to Plastic Collar Quick Connect Fitting Service .
  13. Disconnect the fuel tank EVAP line quick connect fitting from the chassis line. Refer to Plastic Collar Quick Connect Fitting Service .
  14. Cap the fuel and EVAP lines in order to prevent possible fuel and/or EVAP system contamination.
  15. Remove the fuel line bracket bolt (2).
  16. Remove the fuel/EVAP line clip nut (1).
  17. Remove the fuel/EVAP line clips from the frame and crossmember.
  18. Remove the fuel/EVAP line assembly from the vehicle.
    19. Fig 6: Fuel Feed Lines
    GM1855298Courtesy of GENERAL MOTORS CORP.
  19. If equipped with 4WD perform the following steps, disconnect the fuel tank fuel feed line quick connect fitting from the chassis line. Refer to Plastic Collar Quick Connect Fitting Service .
  20. Disconnect the fuel tank EVAP line quick connect fitting from the chassis line. Refer to Plastic Collar Quick Connect Fitting Service .
  21. Cap the fuel and EVAP lines in order to prevent possible fuel and/or EVAP system contamination.
  22. Remove the fuel line bracket bolt (1).
  23. Remove the fuel/EVAP line clip nut (2).
  24. Remove the fuel/EVAP line clips from the frame and crossmember.
  25. Remove the fuel/EVAP line assembly from the vehicle.
scientia non olet · About LEMON Manuals