LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2006 >> Sierra 1500 HD, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 815 (Transfer Case - NVG 246-NP8) >> Diagnostic Information and Procedures >> DTC B0790 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step inspects for the visual operation of the neutral indicator light. Command both the ON and OFF states.
  2. 3:  This step tests for voltage at the Neutral indicator feed side of the transfer case select switch.
  3. 4:  This step verifies that the transfer case shift control module is providing ground to the neutral indicator.
  4. 5:  This step tests if ground is constantly being applied to the neutral indicator.
  5. 6:  This step tests the control circuit of the Neutral indicator for a short to voltage or an open.
  6. 7:  This step tests the control circuit of the neutral indicator for a short to ground.
DTC B0790

Step Action Yes No
Schematic Reference:  Transfer Case Control Schematics  
Connector End View Reference:  Transfer Case Control Connector End Views  
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Install a scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. With the scan tool, command the Neutral Indicator Light ON and OFF.
Does the Neutral Indicator Light turn ON and OFF with each command?		 Go to Testing for Intermittent Conditions and Poor Connections Go to Step 3 
3 
  1. Turn the ignition OFF.
  2. Remove the transfer case select switch.
  3. Disconnect the connector on the transfer case select switch.
  4. Turn the ignition ON.
  5. Probe the ignition 3 voltage circuit with a test lamp that is connected to a good ground.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 10 
4 
  1. Connect a test lamp between the harness connector of the neutral indicator control circuit and the neutral indicator feed circuit.
  2. With the scan tool, command the Neutral indicator ON and OFF.
Does the test lamp turn ON and OFF with each command?		 Go to Step 8  Go to Step 5 
5  Does the test lamp remain illuminated with each command? Go to Step 7  Go to Step 6 
6  Test the neutral indicator control circuit for a short to voltage or an open. Refer to Testing for Continuity and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
7  Test the control circuit of the neutral indicator for a short to ground. Refer to Testing for Short to Ground and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
8 Inspect for poor connections at the transfer case shift control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 11 
9 Inspect for poor connections at the harness connector of the transfer case shift control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
10 Repair the ignition 3 voltage circuit of the transfer case select switch for an open, a high resistance, or a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you complete the repair?		 Go to Step 13  -
11 Replace the transfer case select switch. Refer to Transfer Case Shift Control Switch Replacement .
Did you complete the repair?		 Go to Step 13  -
12
IMPORTANT: After transfer case shift control module replacement and reprogramming, ensure all doors are closed and the key is out of the ignition, then open and close the doors again and wait 2 minutes to avoid incomplete programming or false communication DTCs.
Replace the transfer case shift control module. Refer to Control Module References for replacement, setup, and programming. Perform the Clutch Reset Procedure. Refer to Transfer Case High/Low Clutch Reset .Did you complete the repair?		 Go to Step 13  -
13
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC set?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals