LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2006 >> Sierra 1500 HD, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1543 (Instrument Panel Trim And Console Trim) >> Repair Instructions >> Instrument Panel Service Positioning (with SLT) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2010 GMC Sierra, 2010 GMC Cab & Chassis Sierra, 2010 Chevrolet Silverado, and 2010 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Removing/Installing Instrument Panel Assembly
    GM2006345Courtesy of GENERAL MOTORS CORP.
  1. With the aid of an assistant.
    • Lift the instrument panel assembly (1) up and align the locator pins to the openings in the hinge pillars.
    • Push the instrument panel forward until the instrument panel is in vehicle position.
    2. Fig 2: View Of Bolts Holding Instrument Panel Assembly To Vehicle
    GM2006344Courtesy of GENERAL MOTORS CORP.
  2. Loosely install the 4 bolts (1) on the outer ends of the instrument panel.
    3. Fig 3: View Of Bolts Securing Instrument Carrier Support To Cowl
    GM2006343Courtesy of GENERAL MOTORS CORP.
  3. Loosely install the 2 bolts (1) securing the instrument panel carrier support to the cowl.
    4. CAUTION: Refer to Fastener Caution .
  4. Tighten the 6 bolts securing the instrument panel to the vehicle.

    Tighten:  Tighten the bolts to 22 N.m (16 lb ft).

    5. Fig 4: View Of Bolts Securing Instrument Panel Upper Trim Panel To Cowl
    GM2006341Courtesy of GENERAL MOTORS CORP.
  5. Install the 4 bolts (1) securing the instrument panel upper trim panel to the cowl.

    Tighten:  Tighten the bolts to 9 N.m (80 lb in).

  6. On the left side of the instrument panel.
    • Connect the wire looms securing the wiring harnesses to the left side of the instrument panel.
    • Install the body wiring harness junction block into its bracket.
    • Connect the ground wires to the upper left cowl panel.

      Tighten:  Tighten the nut to 9 N.m (80 lb in).

    • Connect the electrical connections to the instrument panel left electrical center.
  7. On the right side of the instrument panel.
    • Connect the wire looms securing the wiring harnesses to the right side of the instrument panel.
    • Connect the radio antennas.
    • Connect the electrical connection for the instrument panel inflatable restraint module.
    • Connect the electrical connections to the instrument panel right electrical center.
  8. Install the instrument panel center support bracket. Refer to Instrument Panel Center Support Bracket Replacement .
  9. Install the right and left body hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement .
  10. Remove the instrument panel upper trim panel with windshield defroster nozzle grille. Refer to Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (with RPO SLT)  or Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (without RPO SLT) .
  11. Install the windshield pillar garnish moldings. Refer to Windshield Pillar Garnish Molding Replacement .
  12. Install the instrument panel outer trim covers. Refer to Instrument Panel Outer Trim Cover Replacement (with RPO SLT)  or Instrument Panel Outer Trim Cover Replacement (without RPO SLT) .
  13. Install the front floor console. Refer to Front Floor Console Replacement (with RPO SLT)  or Front Floor Console Replacement (without RPO SLT) .
  14. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection (Single Battery) or Battery Negative Cable Disconnection and Connection (Dual Batteries) or Battery Negative Cable Disconnection and Connection (Auxiliary Battery) .
  15. Install the front seats. Refer to Front Seat Replacement - Bucket .
    16. Fig 5: View Of Upper Intermediate Shaft Pinch Bolt, Nut & Steering Column
    GM1701530Courtesy of GENERAL MOTORS CORP.
  16. Install the steering shaft coupling nut (1) and bolt (2) at the steering column.

    Tighten:  Tighten the nut and bolt to 50 N.m (37 lb ft).

    17. Fig 6: Steering Wheel Lock Tool
    GM333146Courtesy of GENERAL MOTORS CORP.
  17. Remove the J 42640:  pin from the steering column.
scientia non olet · About LEMON Manuals