Crankshaft Balancer Installation (RPO HP2)

Tools Required

• J 41478  Crankshaft Front Oil Seal Installer. See Special Tools .
• J 41665  Crankshaft Balancer and Sprocket Installer. See Special Tools .
• J 45059  Angle Meter
• J 46093  Rotor and Flex Plate Holding Tool. See Special Tools .

NOTE: Refer to Fastener Notice .
IMPORTANT:
• On vehicles equipped with RPO HP2, the rotor and flex plate of the electric drive unit MUST be installed to the rear of the engine prior to crankshaft balancer installation.
• The crankshaft balancer installation and bolt tightening involves a 4 stage tightening process. The first pass ensures that the crankshaft balancer is completely installed onto the crankshaft. The second, third and fourth passes tighten the new bolt to the proper torque.
• The used crankshaft balancer bolt is used only during the first pass of the balancer installation procedure. Install a NEW crankshaft balancer bolt and tighten as described in the second, third and fourth passes of the balancer bolt tightening procedure.
Fig 1: Installing J 46093
Courtesy of GENERAL MOTORS CORP.
1. Install the J 46093  (1) and bolts. See Special Tools . The flange of the tool should locate into the hole in the flex plate. Use 2 M10 - 1.5 x 40 mm bolts for proper tool operation.

   Tighten:  Tighten the bolts to 50 N.m (37 lb ft).

IMPORTANT: The balancer should be positioned onto the end of the crankshaft as straight as possible prior to tool installation.
2. Install the balancer onto the end of the crankshaft.
3. Use the J 41665  and the J 41478  in order to install the balancer. See Special Tools .
   Fig 2: Installing Balancer Using J 41665

   Courtesy of GENERAL MOTORS CORP.
   1. Assemble the J 41478  threaded rod, nut, washer and the J 41665  installer. See Special Tools .
   2. Use a wrench and hold the hex end of the threaded rod.
   3. Use a second wrench and rotate the installation tool nut clockwise until the balancer is started onto crankshaft.
   4. Remove and reverse the installation tool. Position the larger end of the installer against the front of the balancer.
   5. Use a wrench and hold the hex end of the threaded rod.
   6. Use a second wrench and rotate the installation tool nut clockwise until the balancer is installed onto the crankshaft.
   7. Remove the balancer installation tools.
4. Install the used crankshaft balancer bolt.
   Fig 3: Crankshaft Balancer And Retaining Bolt

   Courtesy of GENERAL MOTORS CORP.

   Tighten:  Tighten the balancer bolt to 330 N.m (240 lb ft).

5. Remove the used crankshaft balancer bolt.
IMPORTANT: The nose of the crankshaft should be recessed 2.4-4.48 mm (0.094-0.176 in) into the balancer bore.
Fig 4: Identifying Hub To Crankshaft Distance
Courtesy of GENERAL MOTORS CORP.
6. Measure for a correctly installed balancer.

   If the balancer is not installed to the proper dimensions, install the J 41665  and repeat the installation procedure. See Special Tools .

7. Install the NEW crankshaft balancer bolt.
   Fig 5: Crankshaft Balancer And Retaining Bolt

   Courtesy of GENERAL MOTORS CORP.

   Tighten: 

   1. Tighten the crankshaft balancer bolt a first pass to 50 N.m (37 lb ft).
   2. Tighten the crankshaft balancer bolt a second pass to 140 degrees using the J 45059  .

8. Remove the J 46093  . See Special Tools .