LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2005 >> Sierra 1500 HD, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 215 (Automatic Transmission - 5L40-E/5L50-E - (DTC P1834 To DTC P2764)) >> DTC P1876 >> Conditions for Clearing the DTC

Conditions for Clearing the DTC

WARNING: This page is about a different car, the 2005 Cadillac STS. However, it is still accessible from the selected car via links, so may be relevant.
DTC P1876

Step Action Value(s) Yes No
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
    3. IMPORTANT: Before clearing the DTC, use the scan tool in order to record the Failure Records. Using the Clear DTC Information function erases the Failure Records from the TCM.
  3. Record the DTC Failure Records.
  4. Clear the DTC.
  5. Start the engine.
  6. Move the A/T Shift Lever to the Manual position.
  7. Select IMS on the scan tool.
Does the scan tool IMS parameter display Drive 5?		 - Go to Intermittent Conditions in Engine Controls - 3.6L or Intermittent Conditions in Engine Controls - 4.6L Go to Step 3 
3
  1. Select IMS A/B/C/P on the scan tool.
  2. Place the gear select lever in the Manual position.
Does the scan tool IMS A/B/C/P display indicate the specified value for each range?		 HI/HI/HI/HI Go to Step 14  Go to Step 4 
4
  1. Inspect the transmission linkage from the range selector to the manual shift shaft for proper adjustment.
  2. Adjust the linkage as necessary. Refer to Manual Shaft Shift Position Switch Replacement .
Did the linkage require adjustment?		 - Go to Step 19  Go to Step 5 
5
  1. Turn OFF the ignition.
  2. Disconnect the AT inline 20-way connector. Additional DTCs may set.
  3. Turn ON the ignition, with the engine OFF.
  4. Select IMS A/B/C/P on the scan tool.
Does the scan tool IMS A/B/C/P display all HI?		 - Go to Step 6  Go to Step 10 
6
  1. Turn OFF the ignition.
  2. Install the J 45681  jumper harness on the TCM side of the AT inline 20-way connector. See Special Tools .
  3. Turn ON the ignition, with the engine OFF.
  4. Using the DMM and the J 35616  GM terminal test kit, measure the voltage at the Transmission Range (TR) signal A circuit of the J 45681  . See Special Tools . Refer to Automatic Transmission Inline 20-Way Connector End View (5L40-E) or Automatic Transmission Inline 20-Way Connector End View (5L50-E) .
  5. Measure the voltage at the TR signal B of the J 45681  . See Special Tools .
  6. Measure the voltage at the TR signal C of the J 45681  . See Special Tools .
  7. Measure the voltage at the TR signal P of the J 45681  . See Special Tools .
Did you measure ignition voltage at all four terminals?		 - Go to Step 7  Go to Step 11 
7 Install a fused jumper wire from the TR signal A circuit of the J 45681  to ground while monitoring the scan tool IMS A/B/C/P display. See Special Tools .
Refer to Automatic Transmission Inline 20-Way Connector End View (5L40-E) or Automatic Transmission Inline 20-Way Connector End View (5L50-E) .
When the TR signal A circuit is grounded, do any other circuits indicate LOW?		 - Go to Step 12  Go to Step 8 
8 Install a fused jumper wire from the TR signal B circuit of the J 45681  to ground while monitoring the scan tool IMS A/B/C/P display. See Special Tools .
Refer to Automatic Transmission Inline 20-Way Connector End View (5L40-E) or Automatic Transmission Inline 20-Way Connector End View (5L50-E) .
When the TR signal B circuit is grounded, do any other circuits indicate LOW?		 - Go to Step 12  Go to Step 9 
9 Install a fused jumper wire from the TR signal C circuit of the J 45681  to ground while monitoring the scan tool IMS A/B/C/P display. See Special Tools .
Refer to Automatic Transmission Inline 20-Way Connector End View (5L40-E) or Automatic Transmission Inline 20-Way Connector End View (5L50-E) .
When the TR signal C circuit is grounded, do any other circuits indicate LOW?		 - Go to Step 12  Go to Step 13 
10 Test the TR signal circuits of the transmission manual shift shaft switch assembly that did not indicate HI for a short to ground between the TCM connector and the AT inline 20-way connector.
Refer to Testing for Short to Ground and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 19  Go to Step 18 
11 Test the TR signal circuits of the transmission manual shift shaft switch assembly that did not indicate ignition voltage for an open between the TCM connector and the AT inline 20-way connector.
Refer to Testing for Continuity and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 19  Go to Step 18 
12 Test the affected signal circuits of the transmission manual shift shaft switch assembly for a shorted together condition between the TCM connector and the AT inline 20-way connector.
Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 19  Go to Step 18 
13 Test the TR signal circuits of the transmission manual shift shaft switch assembly for an open or shorted condition between the AT inline 20-way connector and the switch.
Refer to Testing for Continuity in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 16  Go to Step 17 
14 Test the ground circuit of the transmission manual shift shaft switch assembly for an open between the AT inline 20-way connector and the chassis.
Refer to Testing for Continuity and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 19  Go to Step 15 
15 Test the ground circuit of the transmission manual shift shaft switch assembly for an open between the AT inline 20-way connector and the switch.
Refer to Testing for Continuity in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 16  Go to Step 17 
16 Replace the automatic transmission wiring harness assembly. Refer to Transmission Internal Electrical Harness Replacement .
Did you complete the replacement?		 - Go to Step 19  -
17 Replace the transmission manual shift shaft switch assembly. Refer to Manual Shaft Shift Position Switch Replacement .
Is the action complete?		 - Go to Step 19  -
18 Replace the TCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Is the action complete?		 - Go to Step 19  -
19 Perform the following procedure in order to verify the repair:
  1. Select DTC.
  2. Select Clear Info.
  3. Start the engine.
  4. Place the A/T Shift Lever in the Manual position.
  5. Select Specific DTC.
  6. Enter DTC P1876.

Has the test run and passed?		 - Go to Step 20  Go to Step 2 
20 With the scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information System OK
scientia non olet · About LEMON Manuals