LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2005 >> Sierra 1500 HD, 4WD >> Repair and Diagnosis >> Brakes >> Mechanical - Hydraulic >> Hydraulic Brake System >> Diagnostic Information and Procedures >> Brake Warning Indicator Always On

Brake Warning Indicator Always On

Brake Warning Indicator Always On

Step Action Yes No
Schematic Reference:  Brake Warning System Schematics  
Connector End View Reference: Hydraulic Brakes Connector End Views ABS Connector End Views in Antilock Brake System and, Computer/Integrating Systems Connector End Views in Computer/Integrating Systems
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Turn OFF the ignition for 5 seconds.
  2. Ensure the park brake is released.
  3. Turn ON the ignition while observing the brake warning indicator.
Does the brake warning indicator illuminate for 3 seconds and then turn OFF?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3
  1. Install a scan tool.
  2. Select the Instrument Panel Cluster Special Functions menu on the scan tool.
  3. Command the Brake Lamp OFF.
Does the brake warning indicator turn OFF?		 Go to Step 4  Go to Step 11 
4
  1. Select Input 1 from the Body Control Module Data Display menu on the scan tool.
  2. Ensure the park brake is released.
  3. Observe the Park Brake status on the scan tool.
Does the scan tool display Released?		 Go to Step 5  Go to Step 6 
5 Disconnect the brake fluid level switch harness connector.
Does the brake warning indicator turn OFF?		 Go to Step 12  Go to Step 8 
6 Disconnect the park brake switch harness connector.
Does the brake warning indicator turn OFF?		 Go to Step 9  Go to Step 7 
7
  1. Disconnect from the body control module (BCM), the harness connector containing the park brake switch output circuit.
  2. Test the park brake switch output circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 10 
8
  1. Disconnect from the electronic brake control module (EBCM), the harness connector containing the brake fluid level sensor signal circuit.
  2. Test the brake fluid level sensor signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 14  Go to Step 13 
9 Replace the park brake switch. Refer to Park Brake Warning Lamp Switch Replacement in Park Brake.
Did you complete the replacement?		 Go to Step 14  -
10
IMPORTANT: Perform the set up procedure for the BCM.
Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.Did you complete the replacement?		 Go to Step 14  -
11 Replace the instrument panel cluster. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 14  -
12 Replace the brake fluid level switch. Refer to Master Cylinder Reservoir Replacement .
Did you complete the replacement?		 Go to Step 14  -
13
IMPORTANT: Following EBCM replacement, use the scan tool to perform the Tire Size Calibration procedure.
Replace the EBCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.Did you complete the replacement?		 Go to Step 14  -
14
  1. Turn OFF the ignition for 5 seconds.
  2. Ensure the park brake is released.
  3. Turn ON the ignition while observing the brake warning indicator.
Does the brake warning indicator illuminate for 3 seconds and then turn OFF?		 System OK Go to Step 2 
scientia non olet · About LEMON Manuals