LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2003 >> Yukon Denali >> Repair and Diagnosis >> External Pages >> Different car >> Section 519 (Engine Mechanical (Introduction) 4.8L, 5.3L & 6.0L) >> Specifications >> Engine Mechanical Specifications (LR4 VIN V)

Engine Mechanical Specifications (LR4 VIN V)

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2004 GMC Yukon XL, 2004 GMC Yukon, 2004 Chevrolet Tahoe, 2004 Chevrolet Suburban, and 2004 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
Engine Mechanical Specifications (LR4 VIN V)

Application Specification
Metric English
General
  • Bore
 96.0-96.018 mm 3.779-3.78 in
  • Compression Ratio
 9.47:1
  • Displacement
 4.8L 293 CID
  • Engine Type
 V8
  • Firing Order
 1-8-7-2-6-5-4-3
  • RPO
 LR4
  • Stroke
 83.0 mm 3.268 in
  • VIN
 V
Spark Plug Gap
  • AC Delco Type 41-974
 1.524 mm 0.06 in
  • AC Delco Type 41-985
 1.016 mm 0.04 in
Block
  • Camshaft Bearing Bore 1 and 5 Diameter - First Design
 59.12-59.17 mm 2.327-2.329 in
  • Camshaft Bearing Bore 2 and 4 Diameter - First Design
 58.87-58.92 mm 2.317-2.319 in
  • Camshaft Bearing Bore 3 Diameter - First Design
 58.62-58.67 mm 2.307-2.309 in
  • Camshaft Bearing Bore 1 and 5 Diameter - Second Design
 59.62-59.67 mm 2.347-2.349 in
  • Camshaft Bearing Bore 2 and 4 Diameter - Second Design
 59.12-59.17 mm 2.327-2.329 in
  • Camshaft Bearing Bore 3 Diameter - Second Design
 58.62-58.67 mm 2.307-2.309 in
  • Crankshaft Main Bearing Bore Diameter
 69.871-69.889 mm 2.75-2.751 in
  • Crankshaft Main Bearing Bore Out-of-Round
 0.006 mm 0.0002 in
  • Cylinder Bore Diameter
 96.0-96.018 mm 3.779-3.78 in
  • Cylinder Bore Taper - Thrust Side
 0.018 mm 0.0007 in
  • Cylinder Head Deck Height - Measuring from the Centerline of Crankshaft to the Deck Face
 234.57-234.82 mm 9.235-9.245 in
  • Cylinder Head Deck Surface Flatness - Measured Within a 152.4 mm (6.0 in) Area
 0.11 mm 0.004 in
  • Cylinder Head Deck Surface Flatness - Measuring the Overall Length of the Block Deck
 0.22 mm 0.008 in
  • Valve Lifter Bore Diameter
 21.417-21.443 mm 0.843-0.844 in
Camshaft
  • Camshaft End Play
 0.025-0.305 mm 0.001-0.012 in
  • Camshaft Journal Diameter
 54.99-55.04 mm 2.164-2.166 in
  • Camshaft Journal Out-of-Round
 0.025 mm 0.001 in
  • Camshaft Lobe Lift - Exhaust
 6.96 mm 0.274 in
  • Camshaft Lobe Lift - Intake
 6.82 mm 0.268 in
  • Camshaft Runout - Measured at the Intermediate Journals
 0.05 mm 0.002 in
Connecting Rod
  • Connecting Rod Bearing Clearance - Production
 0.023-0.065 mm 0.0009-0.0025 in
  • Connecting Rod Bearing Clearance - Service
 0.023-0.076 mm 0.0009-0.003 in
  • Connecting Rod Bore Diameter - Bearing End
 56.505-56.525 mm 2.224-2.225 in
  • Connecting Rod Bore Out-of-Round - Bearing End - Production
 0.004-0.008 mm 0.00015-0.0003 in
  • Connecting Rod Bore Out-of-Round - Bearing End - Service
 0.004-0.008 mm 0.00015-0.0003 in
  • Connecting Rod Side Clearance
 0.11-0.51 mm 0.00433-0.02 in
Crankshaft
  • Connecting Rod Journal Diameter - Production
 53.318-53.338 mm 2.0991-2.0999 in
  • Connecting Rod Journal Diameter - Service
 53.308 mm 2.0987 in
  • Connecting Rod Journal Out-of-Round - Production
 0.005 mm 0.0002 in
  • Connecting Rod Journal Out-of-Round - Service
 0.01 mm 0.0004 in
  • Connecting Rod Journal Taper - Maximum for 1/2 of Journal Length - Production
 0.005 mm 0.0002 in
  • Connecting Rod Journal Taper - Maximum for 1/2 of Journal Length - Service
 0.02 mm 0.00078 in
  • Crankshaft End Play
 0.04-0.2 mm 0.0015-0.0078 in
  • Crankshaft Main Bearing Clearance - Production
 0.02-0.052 mm 0.0008-0.0021 in
  • Crankshaft Main Bearing Clearance - Service
 0.02-0.065 mm 0.0008-0.0025 in
  • Crankshaft Main Journal Diameter - Production
 64.992-65.008 mm 2.558-2.559 in
  • Crankshaft Main Journal Diameter - Service
 64.992 mm 2.558 in
  • Crankshaft Main Journal Out-of-Round - Production
 0.003 mm 0.000118 in
  • Crankshaft Main Journal Out-of-Round - Service
 0.008 mm 0.0003 in
  • Crankshaft Main Journal Taper - Production
 0.01 mm 0.0004 in
  • Crankshaft Main Journal Taper - Service
 0.02 mm 0.00078 in
  • Crankshaft Rear Flange Runout
 0.05 mm 0.002 in
  • Crankshaft Reluctor Ring Runout - Measured 1.0 mm (0.04 in) Below Tooth Diameter
 0.7 mm 0.028 in
  • Crankshaft Thrust Surface - Production
 26.14-26.22 mm 1.029-1.0315 in
  • Crankshaft Thrust Surface - Service
 26.22 mm 1.0315 in
  • Crankshaft Thrust Surface Runout
 0.025 mm 0.001 in
Cylinder Head
  • Cylinder Head Height/Thickness - Measured from the Cylinder Head Deck to the Valve Rocker Arm Cover Seal Surface
 120.2 mm 4.732 in
  • Surface Flatness - Block Deck - Measured Within a 152.4 mm (6.0 in) Area
 0.08 mm 0.003 in
  • Surface Flatness - Block Deck - Measuring the Overall Length of the Cylinder Head
 0.1 mm 0.004 in
  • Surface Flatness - Exhaust Manifold Deck
 0.13 mm 0.005 in
  • Surface Flatness - Intake Manifold Deck
 0.08 mm 0.0031 in
  • Valve Guide Installed Height - Measured from the Spring Seat Surface to the Top of the Guide
 17.32 mm 0.682 in
Intake Manifold
  • Surface Flatness - Measured at Gasket Sealing Surfaces and Measured Within a 200 mm (7.87 in) Area that Includes Two Runner Port Openings
 0.3 mm 0.118 in
Lubrication System
  • Oil Capacity - with Filter
 5.68 liters 6.0 quarts
  • Oil Capacity - without Filter
 4.73 liters 5.0 quarts
  • Oil Pressure - Minimum - Hot
 41 kPa at 1,000 engine RPM
124 kPa at 2,000 engine RPM
165 kPa at 4,000 engine RPM		 6 psig at 1,000 engine RPM
18 psig at 2,000 engine RPM
24 psig at 4,000 engine RPM
Oil Pan
  • Front Cover Alignment - at Oil Pan Surface
 0.0-0.5 mm 0.0-0.02 in
  • Rear Cover Alignment - at Oil Pan Surface
 0.0-0.5 mm 0.0-0.02 in
  • Oil Pan Alignment - to Rear of Engine Block at Transmission Bell Housing Mounting Surface
 0.0-0.25 mm 0.0-0.01 in
Piston Rings
  • Piston Ring End Gap - First Compression Ring - Measured in Cylinder Bore - Production
 0.23-0.44 mm 0.009-0.017 in
  • Piston Ring End Gap - First Compression Ring - Measured in Cylinder Bore - Service
 0.23-0.5 mm 0.009-0.0196 in
  • Piston Ring End Gap - Second Compression Ring - Measured in Cylinder Bore - Production
 0.44-0.7 mm 0.017-0.027 in
  • Piston Ring End Gap - Second Compression Ring - Measured in Cylinder Bore - Service
 0.44-0.76 mm 0.0173-0.03 in
  • Piston Ring End Gap - Oil Control Ring - Measured in Cylinder Bore - Production
 0.18-0.75 mm 0.007-0.029 in
  • Piston Ring End Gap - Oil Control Ring - Measured in Cylinder Bore - Service
 0.18-0.81 mm 0.007-0.032 in
  • Piston Ring to Groove Clearance - First Compression Ring - Production
 0.04-0.085 mm 0.00157-0.00335 in
  • Piston Ring to Groove Clearance - First Compression Ring - Service
 0.04-0.085 mm 0.00157-0.00335 in
  • Piston Ring to Groove Clearance - Second Compression Ring - Production
 0.04-0.078 mm 0.00157-0.0031 in
  • Piston Ring to Groove Clearance - Second Compression Ring - Service
 0.04-0.078 mm 0.00157-0.0031 in
  • Piston Ring to Groove Clearance - Oil Control Ring - Production
 0.012-0.2 mm 0.0005-0.0078 in
  • Piston Ring to Groove Clearance - Oil Control Ring - Service
 0.012-0.2 mm 0.0005-0.0078 in
Pistons and Pins
  • Piston - Piston Diameter - Measured Over Skirt Coating
 96.002-96.036 mm 3.779-3.78 in
  • Piston - Piston to Bore Clearance - Production
 -0.036 to 0.016 mm -0.0014 to 0.0006 in
  • Piston - Piston to Bore Clearance - Service Limit with Skirt Coating Worn Off
 0.071 mm 0.0028 in
  • Pin - Piston Pin Fit in Connecting Rod Bore
 0.02-0.043 mm - interference 0.00078-0.00169 in - interference
  • Pin - Piston Pin Clearance to Piston Pin Bore - Production
 0.007-0.02 mm 0.00027-0.00078 in
  • Pin - Piston Pin Clearance to Piston Pin Bore - Service
 0.007-0.021 mm 0.00027-0.00082 in
  • Pin - Piston Pin Diameter
 23.997-24.0 mm 0.9447-0.9448 in
Valve System
  • Valves - Valve Face Angle
 45 degrees
  • Valves - Valve Face Width
 1.25 mm 0.05 in
  • Valves - Valve Lash
 Net Lash - No Adjustment
  • Valves - Valve Lift - Intake
 11.6 mm 0.457 in
  • Valves - Valve Lift - Exhaust
 11.85 mm 0.466 in
  • Valves - Valve Seat Angle
 46 degrees
  • Valves - Valve Seat Runout
 0.05 mm 0.002 in
  • Valves - Valve Seat Width - Exhaust
 1.78 mm 0.07 in
  • Valves - Seat Width - Intake
 1.02 mm 0.04 in
  • Valves - Valve Stem Diameter - Production
 7.955-7.976 mm 0.313-0.314 in
  • Valves - Valve Stem Diameter - Service
 7.95 mm 0.313 in
  • Valves - Stem-to-Guide Clearance - Production - Intake
 0.025-0.066 mm 0.001-0.0026 in
  • Valves - Stem-to-Guide Clearance - Service - Intake
 0.093 mm 0.0037 in
  • Valves - Stem-to-Guide Clearance - Production - Exhaust
 0.025-0.066 mm 0.001-0.0026 in
  • Valves - Stem-to-Guide Clearance - Service - Exhaust
 0.093 mm 0.0037 in
  • Rocker Arms - Valve Rocker Arm Ratio
 1.70:1
  • Valve Springs - Valve Spring Free Length
 52.9 mm 2.08 in
  • Valve Springs - Installed Height
 45.75 mm 1.8 in
  • Valve Springs - Valve Spring Load - Closed
 340 N at 45.75 mm 76 lb at 1.8 in
  • Valve Springs - Valve Spring Load - Open
 980 N at 33.55 mm 220 lb at 1.32 in
scientia non olet · About LEMON Manuals