LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2003 >> Safari Van Cargo, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 949 (Steering Wheel And Steering Column) >> Repair Instructions >> Lower Bearing and Steering Column Jacket Replacement (Floor Shift Lean Shaft) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
    NOTE: Refer to Fastener Notice in Cautions and Notices.
    IMPORTANT: Replace the steering column support assembly if the steering column support assembly has been staked 3 times.
    Fig 1: View Of Steering Column Support Assembly & TORX(R) Head Screws
    GM306322Courtesy of GENERAL MOTORS CORP.
  1. Attach the steering column support assembly (1) to the steering column jacket assembly with 4 new TORX® head screws (2).

    Tighten:  Tighten the screws to 17 N.m (13 lb ft).

  2. Install the upper bearing assembly.
    Fig 2: View Of Upper Bearing Assembly
    GM1562300Courtesy of GENERAL MOTORS CORP.
    3. Fig 3: Installing Steering Column Shaft Assembly Into The Steering Column Tilt Head Assembly (Floor Shift Lean Shaft)
    GM664272Courtesy of GENERAL MOTORS CORP.
  3. Install the steering column shaft assembly (2) into the steering column tilt head assembly (1).
    4. Fig 4: Installing Steering Column Shaft Assembly Into The Steering Column Support Assembly (Floor Shift Lean Shaft)
    GM322998Courtesy of GENERAL MOTORS CORP.
  4. Install the steering column shaft assembly with the steering column tilt head assembly (1) into the steering column support assembly (2).
  5. Move the tilt knob and push the steering column tilt head assembly up towards the steering column in order to lock the steering wheel lock shoes in place.
    6. IMPORTANT: Replace the steering column support assembly if the steering column support assembly has been staked 3 times.
  6. Lubricate the pivot pins (1) with GM P/N 12346293 (Canadian P/N 992723).
  7. Firmly seat each pivot pin (1) into the steering column tilt head assembly.
    Fig 5: View Of Pivot Pins At Steering Column Assembly
    GM299893Courtesy of GENERAL MOTORS CORP.
  8. Stake the steering column support assembly in 3 locations around each pivot pin (1).
    9. IMPORTANT: Verify that all 12 balls are present and that NO foreign debris is present in the inner race, cage, balls or outer race. The orientation of the cage MUST be as shown to install properly.
    Fig 6: Install The Balls Into The Cage (Floor Shift Lean Shaft)
    GM1565081Courtesy of GENERAL MOTORS CORP.
  9. If necessary, install the balls (2) into the cage (3).
  10. Install the race (1) into the ball and cage assembly.
    Fig 7: Installing Race Into The Ball And Cage Assembly (Floor Shift Lean Shaft)
    GM1565082Courtesy of GENERAL MOTORS CORP.
  11. Install the race, cage and balls into the adapter and bearing assembly (2).
  12. Install the adapter and bearing assembly (1) onto the steering column jacket assembly by performing the following steps:
    1. Align the tab on the adapter and bearing assembly (1) with the slot in the steering column jacket assembly.
    2. Push the adapter and bearing assembly (1) onto the steering column shaft assembly until the tab snaps into the slot.
    Fig 8: View Of Adapter & Bearing Assembly
    GM343881Courtesy of GENERAL MOTORS CORP.
    13. IMPORTANT: Be sure that the electrical contact of the turn signal and multifunction switch assembly (2) rests on the turn signal cancel cam assembly.
    Fig 9: Installing Turn Signal And Multifunction Switch Assembly Onto The Steering Column Tilt Head Assembly (Floor Shift Lean Shaft)
    GM415287Courtesy of GENERAL MOTORS CORP.
  13. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly.
  14. Screw the 2 pan head tapping screws (1) into the turn signal and multifunction switch assembly (2).

    Tighten:  Tighten the screws to 7 N.m (62 lb in).

  15. Install the tilt spring only. Refer to Tilt Spring Replacement .
  16. Install the ignition lock cylinder case. Refer to Ignition Lock Cylinder Case Replacement .
  17. Install the steering column into the vehicle. Refer to Steering Column Replacement .
  18. Enable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR.
scientia non olet · About LEMON Manuals