LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2003 >> Safari Van Cargo, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 70 (Engine Controls Self-Diagnostics - 4.3L) >> Diagnostic Tests >> DTC P0134 & P0154: Ho2S Circuit - Insufficient Activity - Bank 1 & 2, Sensor 1 (Astro & Safari) >> Diagnostic Procedures

Diagnostic Procedures

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2002 GMC Sonoma, 2002 GMC Safari, 2002 GMC Jimmy, 2002 Chevrolet S10 Pickup, and 2002 Chevrolet Blazer. However, it is still accessible from the selected car via links, so may be relevant.
  1. Did you perform the Diagnostic System Check-Engine Controls? If yes, go to next step. If no, see DIAGNOSTIC SYSTEM CHECK - ENGINE CONTROLS  under SELF-DIAGNOSTIC SYSTEM.
    2. NOTE: Allow the engine to cool for one-half hour before proceeding with this diagnostic. This allows the HO2S signal voltage to return to bias voltage, approximately 447 mV.
  2. Turn OFF the ignition. Install a scan tool. Turn ON the ignition, with the engine OFF. Immediately observe the affected HO2S voltage for 2 minutes. Does the HO2S voltage go from bias voltage to more than or less than 300-600 mV? If yes, go to next step. If no, go to step  5.
  3. Start the engine. Allow the engine to reach operating temperature. Raise and hold the engine speed at 1200 RPM for 2 minutes. Observe the HO2S voltage with a scan tool. Is the HO2S voltage varying outside 350-550 mV? If yes, go to next step. If no, go to step  5.
  4. Observe the Freeze Frame/Failure Records data for this DTC. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running DTC or as close to the Freeze Frame/Failure Records data that you observed. Does the DTC fail this ignition cycle? If yes, go to next step. If no, see INTERMITTENT CONDITIONS  under SELF-DIAGNOSTIC SYSTEM.
  5. Turn OFF the ignition. Disconnect the affected HO2S connector. Probe the HO2S low reference circuit with a test lamp that is connected to battery positive. Does the test lamp illuminate? If yes, go to next step. If no, go to step  9.
  6. Jumper the HO2S high signal circuit to the low reference circuit. Turn the ignition ON, with the engine OFF. Observe the HO2S voltage with a scan tool. Is the HO2S voltage less than 200 mV? If yes, go to step  10. If no, go to next step.
  7. Turn OFF the ignition. Disconnect the PCM connector containing the HO2S high signal circuit. Test the HO2S high signal circuit for an open. Did you find and correct the condition? If yes, go to step  22. If no, go to next step.
  8. Test the low reference circuit for an open between terminal "A" of the affected sensor harness connector and the following PCM terminals:
    • C1-29
    • C1-26

    Did you find and correct the condition? If yes, go to step  22. If no, go to step  17.

  9. Disconnect the PCM connector containing the HO2S low reference circuit. Test the low reference circuit for an open between terminal "A" of the affected sensor harness connector and PCM terminal C1-63. Did you find and correct the condition? If yes, go to step  22. If no, go to step  17.
  10. Remove the jumper from the previous step. Is the ENG 1 fuse open? If yes, go to step  13. If no, go to next step.
  11. Turn ON the ignition, with the engine OFF. Probe the HO2S ignition 1 voltage circuit with a test lamp that is connected to a good ground. Does the test lamp illuminate? If yes, go to next step. If no, go to step  18.
  12. Connect a test lamp between the affected HO2S ignition 1 voltage circuit and the HO2S heater ground circuit. Turn ON the ignition, with the engine OFF. Does the test lamp illuminate? If yes, go to step  16. If no, go to step  19.
  13. Disconnect all HO2S pigtail connectors. Test the HO2S ignition 1 voltage circuit for a short to ground. Replace the ENG 1 fuse. Did you find and correct a short to ground in the ignition 1 voltage circuit? If yes, go to step  22. If no, go to next step.
    14. NOTE: Important Perform the following test on HO2S bank 1 sensor 1, HO2S bank 2 sensor 1, and HO2S bank 1 sensor 2. A condition in any sensor will cause this DTC to set.
  14. Test the HO2S ignition 1 voltage circuit, sensor side, for a short to the HO2S body. Did you find the condition? If yes, go to step  20. If no, go to next step.
    15. NOTE: Perform the following test on HO2S bank 1 sensor 1, HO2S bank 2 sensor 1, and HO2S bank 1 sensor 2. A condition in any sensor will cause this DTC to set.
  15. Measure the resistance between the HO2S ignition 1 voltage circuit, sensor side, and the HO2S heater ground circuit, sensor side. Does the resistance of any sensor measure above or below 2-50 ohms? If yes, go to step  20. If no, see INTERMITTENT CONDITIONS  under SELF-DIAGNOSTIC SYSTEM.
  16. Inspect for poor connections at the harness connector of the affected HO2S. Did you find and correct the condition? If yes, go to step  22. If no, go to step  20.
  17. Inspect for poor connections at the harness connector of the PCM. Did you find and correct the condition? If yes, go to step  22. If no, go to step  21.
  18. Repair the open in the ignition 1 voltage circuit. After repairs, go to step  22.
  19. Repair the open in the HO2S heater ground circuit. After repairs, go to step  22.
  20. Replace the affected HO2S. See appropriate REMOVAL, OVERHAUL & INSTALLATION article. After repairs, go to step  22.
  21. Replace the PCM. See appropriate REMOVAL, OVERHAUL & INSTALLATION article. Reprogram PCM. See POWERTRAIN CONTROL MODULE  under PROGRAMMING. After repairs, go to next step.
  22. Clear the DTCs with a scan tool. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running DTC. Does the DTC run and pass? If yes, go to next step. If no, go to step  2.
  23. Observe the stored information, Capture Info with a scan tool. Does the scan tool display any DTCs that you have not diagnosed? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no, system is okay.
scientia non olet · About LEMON Manuals