LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2003 >> Safari Van Cargo, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1585 (Seat Belt System) >> Repair Instructions >> Seat Belt Replacement - Center Rear >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2007 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Retractor Cover & Fasteners
    GM986477Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice .
    IMPORTANT: Apply Permatex® 24200 on all restraint fasteners prior to installation.
  1. Position the retractor into the rear seat back frame and install the fasteners.

    Tighten:  Tighten the fasteners to 45 N.m (33 lb ft).

  2. Position the retractor cover over the shoulder belt retractor and install the TORX® fasteners.

    Tighten:  Tighten the fasteners to 20 N.m (15 lb ft).

    3. Fig 2: Identifying Shoulder Belt & Escutcheon Through Rear Seat Back Cover
    GM986393Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Verify that the shoulder belt is not twisted.
  3. Route the webbing and the escutcheon through the seat back trim cover.
  4. Continue to install the seat back trim cover by pressing over the hook and loop locations to ensure proper engagement.
  5. Install the seat belt webbing bezel.
    1. Slide the bezel inboard into the opening in the seat back.
    2. Apply pressure along the outboard edge of the bezel to engage the locking tabs.
  6. Route the recliner cable between the seat back and the panel.
    7. Fig 3: Removing/Installing Headrest Guides
    GM981023Courtesy of GENERAL MOTORS CORP.
  7. Install the head rest guides by pushing down until the tabs engage on the frame.
    8. Fig 4: Seat Back Recliner Handle & Cable
    GM986676Courtesy of GENERAL MOTORS CORP.
  8. Connect the recliner handle to the recliner cable.
  9. Install the recliner handle and fastener.

    Tighten:  Tighten the fasteners to 2.5 N.m (22 lb in).

  10. Install the inboard seat frame to the recliner and install the bolts.

    Tighten:  Tighten the bolts to 50 N.m (37 lb ft).

  11. Connect the J-hook retainer to the rear seat back trim cover.
  12. Install the seat back outer bolt.

    Tighten:  Tighten the bolt to 45 N.m (33 lb ft).

    13. Fig 5: Disconnecting Latch Cable
    GM986321Courtesy of GENERAL MOTORS CORP.
  13. Connect the release cable to the recliner mechanism.
    14. Fig 6: Seat Cushion & Buckle
    GM987342Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Verify that the shoulder belt is not twisted.
  14. Route the shoulder belt through the seat cushion opening and install the fastener.

    Tighten:  Tighten the fastener to 50 N.m (37 lb ft).

    15. Fig 7: Removing/Installing Fastener From The Rear Seat Back Latch
    GM982101Courtesy of GENERAL MOTORS CORP.
  15. Install the child tether escutcheons.
    16. Fig 8: Removing/Installing Child Comfort Guide
    GM982115Courtesy of GENERAL MOTORS CORP.
  16. Install the comfort guide.
  17. Install the rear seat back head restraint. Refer to Rear Seat Head Restraint Replacement in Seats.
  18. Install the rear seat assembly. Refer to Rear Seat Replacement .
scientia non olet · About LEMON Manuals