LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2003 >> Safari Van Cargo, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1567 (Engine Controls And Fuel - 2.2L (L61) - DTC P0201 To DTC P0651) >> DTC P0340 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 4:  This step determines if the Ignition system is working correctly.
  2. 5:  This step determines if the interconnect is bad or if a poor connection exists between the ICM and the Coil Cassette.
DTC P0340

Step Action Values Yes No
Schematic Reference:  Engine Controls Schematics 
Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Install the scan tool.
  2. Start and idle the engine.
  3. Monitor the camshaft position (CMP) Active Counter parameter with the scan tool.
Does the scan tool indicate the CMP active counter is incrementing?		 - Go to Step 3  Go to Step 4 
3
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 4  Go to Diagnostic Aids
4 
  1. Turn OFF the ignition.
  2. Disconnect the ignition control module (ICM) electrical connector.
  3. Connect a jumper wire from each terminal, except the CMP signal circuit, in the ICM harness connector to the corresponding terminal at the ICM. Refer to Using Connector Test Adapters .
  4. Measure the DC duty cycle between the CMP signal circuit at the ICM and a good ground.
  5. Start the engine.
Is the duty cycle within the specified range?		 45-55% Go to Step 6  Go to Step 5 
5 
  1. Turn OFF the ignition.
  2. Remove the jumper wires from the ICM.
  3. Remove the ICM from the Ignition Coil Cassette. Refer to Ignition Control Module Replacement .
  4. Remove the interconnect from between the coil cassette and the ICM.
  5. Inspect the interconnect for a poor connection at the coil cassette or at the ICM.
Did you find and correct the condition?		 - Go to Step 11  Go to Step 7 
6 Test the CMP signal circuit for the following conditions:
  • An open
  • High resistance
  • A short to ground
  • A short to voltage

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 11  Go to Step 8 
7 Test for an intermittent and for a poor connection at the ICM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 11  Go to Step 9 
8 Test for an intermittent and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 11  Go to Step 10 
9 Replace the ICM. Refer to Ignition Control Module Replacement .
Did you complete the replacement?		 - Go to Step 11  -
10 Replace the ECM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 11  -
11
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 12 
12 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals