LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2003 >> Safari Van Cargo, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1564 (Engine Controls And Fuel - 3.5L (L66) - DTC P0030 To DTC P0222) >> DTC P0107 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 1:  The Diagnostic System Check - Vehicle prompts the technician to complete some basic checks and store the Freeze Frame data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
  2. 2:  This step determines if a MAP sensor malfunction is present. The input signal of the MAP sensor should indicate atmospheric pressure with the ignition ON, engine OFF. The MAP sensor will vary with atmospheric pressure. A typical pressure at sea level is 100 kPa (29-30 in Hg).
  3. 5:  This step checks for an open in the MAP sensor reference voltage circuit.
  4. 6:  The MAP sensor signal circuit carries a 5 volt bias that can be measured with the DMM. If the measured voltage is near zero there is a short to ground or a faulty PCM.
DTC P0107

Step Action Values Yes No
Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views
1  Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Turn ON the ignition, with the engine OFF.
  2. Observe the manifold absolute pressure (MAP) sensor parameter on the scan tool.
Is the MAP sensor value within the specified range?		 95-100 kPa Go to Step 3  Go to Step 4 
3
  1. Use the scan tool in order to clear the DTCs.
  2. Start the engine.
  3. Operate the vehicle within the Freeze Frame conditions as specified or within the Conditions for Running the DTC. Review the supporting text.
Does the DTC fail this ignition?		 - Go to Step 4  Go to Diagnostic Aids In This Test
4 Was DTC P0502 also set? - Go to Step 9  Go to Step 5 
5 
  1. Turn OFF the ignition.
  2. Disconnect the MAP sensor electrical connector.
  3. Turn ON the ignition, with the engine OFF.
  4. Measure the 5-volt reference circuit of the MAP sensor with a DMM.
Is the voltage near the specified value?		 5.0 V Go to Step 6  Go to Step 8 
6  Measure the voltage of the MAP sensor signal circuit with a DMM.
Is the voltage near the specified value?		 4.9 V Go to Step 10  Go to Step 7 
7
  1. Test the MAP sensor signal circuit for a short to ground.
  2. Repair as necessary. Refer to Wiring Repairs .
Did you find and correct a condition?		 - Go to Step 12  Go to Step 11 
8 Repair the open in the 5-volt reference sensor circuit between the MAP sensor and SP114. Refer to Wiring Repairs .
Is the action complete?		 - Go to Step 12  -
9 Repair the open in the 5-volt reference sensor circuit between the powertrain control module (PCM) and SP114. Refer to Wiring Repairs .
Is the action complete?		 - Go to Step 12  -
10 Replace the MAP sensor. Refer to Manifold Absolute Pressure Sensor Replacement .
Did you complete the replacement?		 - Go to Step 12  -
11
  1. Replace the PCM. Refer to Control Module References for replacement, setup, and programming.
  2. Perform the idle learn procedure. Refer to Idle Learn .
Did you complete the replacement?		 - Go to Step 12  -
12
  1. Use the scan tool in order to clear the DTCs.
  2. Turn the ignition OFF for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC or until the DTC P0107 diagnostic has passed.
Does the DTC run and pass?		 - Go to Step 13  Go to Step 2 
13 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals