Test Description
WARNING: This page is about a different car, the 2003 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
The number below refers to the step number on the diagnostic table.
- 12: Check the connection by removing and securely reinstalling before replacement of the HVAC control is considered.
HVAC Compressor Clutch Does Not Disengage
| Step | Action | Values | Yes | No |
|---|---|---|---|---|
| Schematic Reference: HVAC Schematics Connector End View Reference: HVAC Connector End Views DEFINITION: The A/C compressor clutch will not disengage when an A/C request has not been made and a Powertrain DTC has not been set. |
||||
| 1 | Did you perform the HVAC Diagnostic System Check? | - | Go to Step 2 | Go to Diagnostic System Check - HVAC Systems - Manual |
| 2 |
|
- | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems |
| 3 | With a scan tool, observe the A/C request signal parameter in the Engine Control Module (ECM), General Info Inputs data list. Does the scan tool indicate that the A/C request signal parameter is YES? |
- | Go to Step 4 | Go to Step 6 |
| 4 | Test the A/C request signal circuit for a short to voltage. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 5 |
| 5 |
|
- | Go to Step 13 | Go to Step 12 |
| 6 | With a scan tool, command the A/C compressor clutch relay ON and OFF. Does the A/C compressor clutch relay turn ON and OFF with each command? |
- | Go to Step 7 | Go to Step 9 |
| 7 | Remove the A/C compressor clutch relay. Is the A/C compressor ON? |
- | Go to Step 10 | Go to Step 8 |
| 8 | Measure the resistance between the switch side A/C compressor clutch relay terminals. Does the resistance measurement equal the specified value? |
Infinity | Go to Step 9 | Go to Step 11 |
| 9 | Test the A/C clutch relay control circuit for a short to ground. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 13 |
| 10 | Test the A/C compressor clutch supply voltage circuit for a short to voltage. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 15 |
| 11 | Inspect for poor connections at the A/C compressor clutch relay. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 14 |
| 12 | Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 16 |
| 13 | Inspect for poor connections at the harness connector of the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 18 | Go to Step 17 |
| 14 | Replace the A/C compressor clutch relay. Did you complete the replacement? |
- | Go to Step 18 | - |
| 15 | Replace the A/C compressor clutch. Refer to Compressor Replacement
in Heating, Ventilation, and Air Conditioning. Did you complete the replacement? |
- | Go to Step 18 | - |
| 16 | Replace the HVAC control module. Refer to HVAC Control Module Replacement . Did you complete the replacement? |
- | Go to Step 18 | - |
| 17 |
IMPORTANT:
Perform the reprogramming procedure for the ECM. Replace the ECM. Refer to ENGINE CONTROL MODULE
.Did you complete the replacement? |
- | Go to Step 18 | - |
| 18 | Operate the system in order to verify the repair. Did you correct the condition? |
- | System OK | Go to Step 3 |