LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2003 >> Safari Van Cargo, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1330 (Engine Mechanical (Repair Instructions 3 Of 3) - 5.7L) >> Off-Vehicle Repair Instructions - Part 3 >> Oil Pan Installation

Oil Pan Installation

WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Front Cover Gasket That Protrude & Oil Pan Surface
    GM63176Courtesy of GENERAL MOTORS CORP.
    IMPORTANT:
    • All gasket surfaces should be free of oil or other foreign material during assembly.
    • The alignment of the structural oil pan is critical. The rear bolt hole locations of the oil pan provide mounting points for the transmission housing. To ensure the rigidity of the powertrain and correct transmission alignment, it is important that the rear of the block and the rear of the oil pan are flush or even. The rear of the oil pan must NEVER protrude beyond the engine block and transmission housing plane.
    • DO NOT use the oil pan gaskets again.
    • It is not necessary to rivet the NEW gasket to the oil pan.
    • It is not necessary to remove the oil level sensor prior to oil pan installation.
  1. Apply a 5 mm (0.2 in) bead of sealant GM P/N 12378190 or equivalent 20 mm (0.8 in) long to the engine block. Apply the sealant directly onto the tabs of the front cover gasket that protrude into the oil pan surface.
    2. Fig 2: View Of Sealant On Engine Rear Cover Gasket Tabs
    GM63175Courtesy of GENERAL MOTORS CORP.
  2. Apply a 5 mm (0.2 in) bead of sealant GM P/N 12378190 or equivalent 20 mm (0.8 in) long to the engine block. Apply the sealant directly onto the tabs of the rear cover gasket that protrude into the oil pan surface.
    3. Fig 3: Oil Pan, Upper Gasket, Bolts & Engine Block
    GM416764Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Be sure to align the oil gallery passages in the oil pan and engine block properly with the oil pan gasket.
  3. Pre-assemble the oil pan gasket to the pan, upper.
    1. Install the gasket onto the oil pan, upper.
    2. Install the oil pan bolts to the pan and through the gasket.
  4. Install the oil pan, upper, gasket and bolts to the engine block.
  5. Tighten bolts finger tight. Do not overtighten.
  6. Place a straight edge across the rear of the engine block and the rear of the oil pan at the transmission housing mounting surfaces.
    7. Fig 4: Measuring The Oil Pan-To-Engine Block Alignment
    GM63172Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice in Cautions and Notices.
  7. Align the oil pan - upper - until the rear of engine block and rear of oil pan are flush or even.

    Tighten: 

    1. Tighten the oil pan-to-block and oil pan-to-front cover bolts to 25 N.m (18 lb ft).
    2. Tighten the oil pan-to-rear cover bolts to 12 N.m (106 lb in).

  8. Measure the oil pan-to-engine block alignment.
    1. Place a straight edge across the rear of the engine block and rear of oil pan at the transmission housing mounting surfaces.
      2. IMPORTANT: The rear of the oil pan must NEVER protrude beyond the engine block and transmission housing mounting surfaces.
    2. Insert a feeler gage between the straight edge and the oil pan transmission housing mounting surface and check to make sure that there is no more than a 0.25 mm (0.01 in) gap between the pan and straight edge.
    3. If the oil pan alignment is not within specifications, remove the oil pan and repeat the above procedure.
    9. Fig 5: Oil Pan, Lower & Gasket
    GM1272836Courtesy of GENERAL MOTORS CORP.
  9. Install the oil pan, lower (454), and gasket (453).
    10. Fig 6: Oil Pan & Lower Bolts
    GM414783Courtesy of GENERAL MOTORS CORP.
  10. Install the oil pan, lower bolts (1-15).

    Tighten:  Tighten the oil pan, lower bolts to 12 N.m (106 lb in).

    Tighten the bolts in a crossing pattern, alternating from side to side.

    11. Fig 7: Oil Level Sensor
    GM63114Courtesy of GENERAL MOTORS CORP.
  11. Install the oil level sensor.

    Tighten:  Tighten the oil level sensor to 13 N.m (115 lb in).

    12. Fig 8: View Of Left Closeout Cover & Bolt
    GM178477Courtesy of GENERAL MOTORS CORP.
  12. Install the left closeout cover and bolt.

    Tighten:  Tighten the closeout cover bolt to 12 N.m (106 lb in).

    13. Fig 9: View Of Right Closeout Cover & Bolt
    GM178480Courtesy of GENERAL MOTORS CORP.
  13. Install the right closeout cover and bolt.

    Tighten:  Tighten the closeout cover bolt to 12 N.m (106 lb in).

scientia non olet · About LEMON Manuals