LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2003 >> Safari Van Cargo, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1074 (Supplemental Inflatable Restraint System) >> Diagnostic Information and Procedures >> DTC B0100, B0101, B0102, B0103, B0104, or B0105: Temperature Control Circuit >> Test Description

Test Description

WARNING: This page is about a different car, the 2004 Pontiac Aztek and 2004 Buick Rendezvous. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 7:  Tests the EFS signal and EFS voltage circuits for an open or high resistance
  2. 8:  Tests between the EFS signal and EFS voltage circuits for continuity
  3. 9:  Tests the EFS signal and EFS voltage circuits for a short to voltage
DTC B0100, B0101, B0102, B0103, B0104, or B0105

Step Action Yes No
Schematic Reference: SIR Schematics 
1 Did you perform the Diagnostic System Check - SIR? Go to Step 2  Go to Diagnostic System Check - SIR 
2
  1. Install A scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool to request SIR DTCs displayed.
Does the scan tool indicate that DTC B0101, B0102, B0104, or B0105 is current?		 Go to Step 10  Go to Step 3 
3
  1. Turn OFF the ignition.
  2. If DTC B0100 is current, disconnect the inflatable restraint Front End Sensor (EFS) - LF connector. If DTC B0103 is current, disconnect the EFS-RF connector. The EFS is also known as the inflatable restraint front end discriminating sensor. Refer to Inflatable Restraint Front End Sensor Replacement .
  3. Inspect both the component and harness sides of the connector for damage or corrosion. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Does the connector exhibit any signs of damage or corrosion?		 Go to Step 4  Go to Step 5 
4
  1. If the component side of the EFS connector is damaged, the EFS must be replaced. Refer to Inflatable Restraint Front End Sensor Replacement .
  2. If the harness side of the EFS connector is damaged, replace the harness side of the connector. Refer to Connector Repairs in Wiring Systems.
Did you complete the repair?		 Go to Step 11  -
5
  1. Turn OFF the ignition.
  2. Disconnect the Inflatable Restraint Sensing and Diagnostic Module (SDM) connector. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
  3. Inspect both the component and harness sides of the SDM connector for damage or corrosion. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Does the connector exhibit any signs of damage or corrosion?		 Go to Step 6  Go to Step 7 
6
  1. If the component side of the SDM connector is damaged, the SDM must be replaced. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
  2. If the harness side of the SDM connector is damaged, replace the harness side of the connector. Refer to Connector Repairs in Wiring Systems.
Did you complete the repair?		 Go to Step 11  -
7 
  1. If DTC B0100 is current, disconnect the EFS-LF connector. If DTC B0103 is current, disconnect the EFS-RF connector.
  2. Test both the EFS signal and EFS voltage circuits for an open or high resistance between the SDM connector and the EFS connector. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 11  Go to Step 8 
8  Test for continuity between the EFS signal circuit and the EFS voltage circuit on the SDM connector. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 11  Go to Step 9 
9 
  1. Turn ON the ignition, with the engine OFF.
  2. Test both EFS signal and EFS voltage circuits for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 11  Go to Step 10 
10
  1. Turn OFF the ignition.
  2. If DTC B0100, B0101, or B0102 was current replace the EFS-LF. If DTC B0103, B0104, or B0105 was current replace the EFS-RF. Refer to Inflatable Restraint Front End Sensor Replacement .
Did you complete the replacement?		 Go to Step 11  -
11
  1. Reconnect all SIR components.
  2. Use the scan tool in order to Clear the DTCs.
  3. Operate the vehicle within the Conditions for Running the DTC as specified in the text.
Does the DTC reset?		 Go to Step 12  System OK
12
  1. Turn OFF the ignition.
  2. Replace the SDM. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
Did you complete the replacement?		 Go to Step 13  -
13
  1. Turn ON the ignition, with the engine OFF
  2. Use the scan tool in order to Clear the DTCs.
  3. Operate the vehicle within the Conditions for Running the DTC as specified in the text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals