LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2003 >> Safari Van Cargo, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1001 (Engine Controls - 6.6L (LLY) (Troubleshooting & Diagnosis)) >> Troubleshooting >> Fuel System Diagnosis >> Diagnostic Aids

Diagnostic Aids

WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.

The following conditions may cause an air leak into the fuel supply system:

Fuel System Diagnosis

Step Action Yes No
1
IMPORTANT: Ensure that a sufficient amount of fuel is in the fuel tank to run the vehicle.
  1. Install the J 44638  Vacuum Gage to the fuel system service port on the right front side of the engine.
  2. Prime the fuel system until 10 psi is indicated on the J 44638  .
    3. IMPORTANT: It may be necessary to remove engine components for the visual inspections.
  3. Visually inspect the following items for restrictions or leaks:
    • Fuel injector control module fuel line connections
    • Hoses and lines that are flattening when the engine is running, or have kinks that would restrict the flow of fuel
    • Fuel leaks between the fuel filter/heater element housing and the fuel injection pump
Did you find and correct the condition?		 Go to Step 21  Go to Step 2 
2 Does the fuel system pressure drop below 2 psi in less than 1 minute? Go to Step 12  Go to Step 3 
3
  1. Disconnect the fuel supply line at the engine. Refer to Quick Connect Fitting(s) Service (Metal Collar) .
  2. Cap off the fuel supply pipe on the engine with a rubber plug and clamp.
  3. Disconnect the fuel return line at the engine. Refer to Quick Connect Fitting(s) Service (Metal Collar) .
  4. Install a J 23738-A  Mityvac on the fuel return pipe on the engine.
  5. Apply at least 25 inches Hg of vacuum to the fuel return pipe and wait for at least 1 minute for the system to stabilize. Repeat this step 6 additional times.
Does the J 23738-A  gage indicate that vacuum dropped below 8 inches Hg of vacuum within 10 minutes?		 Go to Step 7  Go to Step 4 
4
  1. Connect the fuel supply line at the engine.
  2. Disconnect the chassis fuel supply line from the fuel sender at the fuel tank. Refer to Quick Connect Fitting(s) Service (Metal Collar) .
  3. Plug the chassis fuel supply line.
  4. Apply at least 25 inches Hg of vacuum to the fuel return pipe with the J 23738-A  and wait more than 1 minute for the system to stabilize.
  5. Repeat the previous step 10 times.
  6. Observe the J 23738-A  .
Does the vacuum drop below 8 Hg of vacuum within 10 minutes?		 Go to Step 15  Go to Step 5 
5
  1. Reconnect the return line at the engine.
  2. Install a transparent hose between the fuel injection control module (FICM) outlet and the fuel filter inlet with a vertical loop to observe the incoming fuel for air bubbles.
  3. Install all components and lines that were previously disconnected or removed.
  4. Prime the fuel system 30 times to remove the air from the fuel hoses.
  5. Attempt to start the engine.
Did the engine start?		 Go to Step 6  Go to Step 12 
6
  1. Run the engine for at least 10 minutes to allow the fuel system to stabilize, and purge any air from the system.
  2. Observe the fuel in the transparent hose.
Are there any air bubbles entering the transparent hose?		 Go to Step 10  Go to Step 21 
7
  1. Disconnect the fuel outlet hose from the outlet pipe of the fuel filter/heater element housing.
  2. Open the drain on the fuel filter/heater element housing and drain the fuel into a suitable container.
  3. Close the drain.
  4. Install a J 23738-A  on the outlet port of the fuel filter/heater element housing.
  5. Apply 15 inches Hg of vacuum to the fuel pipe and observe the gage.
Does the vacuum drop?		 Go to Step 13  Go to Step 8 
8
  1. Connect the fuel supply line at the engine.
  2. Remove the J 23738-A  from the outlet port of the fuel filter assembly and install it on the fuel outlet hose.
  3. Remove the supply hose from the fuel injection pump and plug the hose.
  4. Apply 15 inches Hg of vacuum and observe the reading.
Does the vacuum drop?		 Go to Step 16  Go to Step 9 
9
  1. Disconnect the fuel injection pump return hose.
  2. Cap off the fuel return pipe on the fuel injection pump with a rubber plug, and clamp the plug.
  3. Install a J 23738-A  to the fuel inlet pipe of the fuel injection pump.
  4. Apply 20 inches Hg of vacuum and observe the reading.
Does the vacuum drop?		 Go to Step 18  Go to Step 17 
10
  1. Remove the front fuel tank. Refer to Fuel Tank Replacement (Pickup) or Fuel Tank Replacement (Cab/Chassis - Front) or Fuel Tank Replacement (Cab/Chassis - Rear) .
  2. Remove the fuel sender from the fuel tank. Refer to Fuel Sender Assembly Replacement .
  3. Remove the strainer from the fuel sender and plug the bottom end of the pickup tube.
  4. Install a J 23738-A  to the upper end of the pickup tube.
  5. Apply 15 inches Hg of vacuum and observe the reading.
Does the vacuum drop?		 Go to Step 20  Go to Step 11 
11
  1. Install the fuel sender, fuel tank and connect all fuel system connections that were previously disconnected. Refer to Fuel Sender Assembly Replacement and Fuel Tank Replacement (Pickup) or Fuel Tank Replacement (Cab/Chassis - Front) or Fuel Tank Replacement (Cab/Chassis - Rear) .
  2. Prime the fuel system 30 times, or until fuel pressure is 10 psi, to remove the air from the fuel system. Air will be forced out of the system within 2 minutes.
  3. Start and run the engine.
  4. Observe the fuel entering the transparent hose for air bubbles.
Are any air bubbles present in the transparent hose?		 Go to Diagnostic Aids Go to Step 21 
12
  1. Prime the fuel system 30 times, or until fuel pressure is 10 psi, to remove the air from the fuel system. Air will be forced out of the system within 2 minutes.
  2. Remove the hose from the fuel filter/heater element housing outlet fitting and plug the hose.
  3. Verify that the J 44638  is installed.
  4. Remove the ignition 1 relay.
  5. Crank the engine 2-3 times in 15-second intervals and observe the J 44638  .
Does the J 44638  indicate more than 5 inches Hg of vacuum?		 Go to Step 21  Go to Step 18 
13
  1. Disconnect the fuel supply line from the fuel filter/heater element housing port. Install the J 23738-A  to the fuel supply line.
  2. Apply 15 inches Hg of vacuum and observe the reading.
Does the vacuum drop?		 Go to Step 14  Go to Step 19 
14 Repair the air leak in the fuel supply pipe on the engine.
Did you complete the repair?		 Go to Step 21  -
15 Repair the air leak in the fuel supply line between the engine and the fuel tank sending unit.
Did you complete the repair?		 Go to Step 21  -
16 Repair the leak between the fuel filter/heater element housing outlet and the fuel injection pump inlet.
Did you complete the repair?		 Go to Step 21  -
17 Replace the fuel injection pump inlet supply hose. Refer to Fuel Hose Replacement - Fuel Injection Pump to Fuel Feed Block .
Did you complete the replacement?		 Go to Step 21  -
18 Replace the fuel injection pump. Refer to Fuel Injection Pump Replacement .
Did you complete the replacement?		 Go to Step 21  -
19
IMPORTANT: Before replacing the fuel filter/heater element housing, inspect the fuel vent screw for damage or cross threading. Replace the vent screw with O-ring if either condition is found.
Replace the fuel filter/heater element housing. Refer to Fuel Filter/Heater Element Housing Replacement .Did you complete the replacement?		 Go to Step 21  -
20 Replace the fuel tank sending unit. Refer to Fuel Sender Assembly Replacement .
Did you complete the replacement?		 Go to Step 21  -
21
  1. Remove the transparent hose, if necessary, and attach any disconnected components or fuel lines.
  2. Clean any fuel spills.
  3. Prime the fuel system 30 times to remove the air in the fuel hoses.
  4. Start the engine. If the engine starts and stalls, prime fuel system an additional 30 times.
  5. Run the engine to ensure no fuel leaks exist.
Is the customer concern corrected?		 System OK Go to Symptoms - Engine Controls 
scientia non olet · About LEMON Manuals