LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2002 >> Jimmy 2D Utility, Automatic, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 971 (Automatic Transmission - 4L80-E/4L85-E, Diagnosis (P0218 To P2771)) >> Diagnosis >> DTC P0719 >> Test Description

Test Description

WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 4:  This step tests for TCC/Stop lamp switch voltage to the PCM connector.
  2. 7:  This step isolates the TCC/Stop lamp switch as a source for setting the DTC.
  3. 10:  This step tests for a short to ground in the brake fuse circuit.
  4. 12:  This step tests for a short to ground in the TCC brake switch signal circuit, from the TCC/Stop lamp switch to the PCM.
  5. 13:  This step isolates the PCM as a source for causing the fuse to open.
DTC P0719

Step Action Value(s) Yes No
1 Did you perform the Diagnostic System Check - Engine Controls? - Go to Step 2  Go to Diagnostic System Check - Engine Controls in Engine Controls - 4.8L, 5.3L, and 6.0L
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
    3. IMPORTANT: Before clearing the DTCs, use the scan tool in order to record the Failure Records. Using the Clear Info function erases the Failure Records from the PCM.
  3. Record the Failure Records.
  4. Clear the DTCs.
    5. CAUTION: Refer to SIR Caution in Cautions and Notices.
  5. Select TCC Brake Switch on the scan tool.
  6. Do not apply the brake pedal.
Does the scan tool TCC/Brake Switch indicate CLOSED, when the brake pedal is not applied?		 - Go to Intermittent Conditions in Engine Controls - 4.8L, 5.3L, and 6.0L Go to Step 3 
3
  1. Remove the brake fuse.
  2. Inspect the brake fuse for an open.

    Refer to Circuit Protection - Fuses in Wiring Systems.

Is the fuse open?		 - Go to Step 10  Go to Step 4 
4 
  1. Turn OFF the ignition.
  2. Disconnect the PCM connector C1 from the PCM.
  3. Connect a 12 volt test lamp to a good ground.
  4. Using the J 35616  GM terminal test kit and the 12 volt test lamp, probe terminal C1-33.
  5. Install the fuse.
  6. Turn ON the ignition, with the engine OFF.
  7. Do not apply the brake pedal.
Does the test lamp illuminate?		 - Go to Step 15  Go to Step 5 
5
  1. Turn OFF the ignition.
  2. Remove the connector from the TCC/Stop lamp switch.
  3. Use the DMM to measure B+ voltage at terminal D of the brake switch connector.
  4. Turn ON the ignition, with the engine OFF.
Does the voltage measure within the specified value?		 10-13 V Go to Step 7  Go to Step 6 
6
IMPORTANT: The condition that affects this circuit may exist in other connecting branches of the circuit. Refer to Power Distribution Schematics in Wiring Systems for complete circuit distribution.
Test the brake fuse circuit for an open.Did you find and correct the condition?		 - Go to Step 16  -
7 
  1. Turn ON the ignition, with the engine OFF.
  2. Install a fused jumper wire from terminal C to terminal D of the TCC/Stop lamp switch connector.
  3. Probe the PCM connector terminal C1-33 with the test lamp.
Does the test lamp illuminate?		 - Go to Step 9  Go to Step 8 
8
IMPORTANT: The condition that affects this circuit may exist in other connecting branches of the circuit. Refer to Power Distribution Schematics in Wiring Systems for complete circuit distribution.
Test the TCC brake switch signal circuit for an open.Did you find and correct the condition?		 - Go to Step 16  -
9 Replace the TCC/Stop lamp switch.
Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?		 - Go to Step 16  -
10 
  1. Turn ON the ignition, with the engine OFF.
  2. Apply and hold the brake pedal.
  3. Install a new fuse while keeping the brake pedal applied.
Does the fuse open with the brake pedal applied?		 - Go to Step 11  Go to Step 12 
11
IMPORTANT: The condition that affects this circuit may exist in other connecting branches of the circuit. Refer to Power Distribution Schematics in Wiring Systems for complete circuit distribution.
Test the brake fuse circuit for a short to ground.Refer to Testing for a Short to Voltage in Wiring Systems.Did you find and correct the condition?		 - Go to Step 16  -
12  With the key in the RUN position, release the brake pedal.
Does the fuse open when the brake pedal is released?		 - Go to Step 13  Go to Intermittent Conditions in Engine Controls - 4.8L, 5.3L, and 6.0L
13 
  1. Disconnect the PCM connector C1 from the PCM. Additional DTCs may set.
  2. Turn ON the ignition, with the engine OFF.
  3. Install a new fuse.
  4. Do not apply the brake pedal.
Does the fuse open?		 - Go to Step 14  Go to Step 15 
14
IMPORTANT: The condition that affects this circuit may exist in other connecting branches of the circuit. Refer to Power Distribution Schematics in Wiring Systems for complete circuit distribution.
Test the TCC brake switch signal circuit for a short to ground.Refer to Testing for Short to Ground in Wiring Systems.Did you find and correct the condition?		 - Go to Step 16  -
15 Replace the PCM.
Refer to Powertrain Control Module (PCM) Replacement in Engine Controls - 4.8L, 5.3L, and 6.0L.
Did you complete the replacement?		 - Go to Step 16  -
16 Perform the following procedure in order to verify the repair:
  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle under the following conditions:
    • Turn ON the ignition, with the engine OFF.
    • The brake pedal is not applied.
    • Select TCC Brake Switch on the scan tool.

Does the TCC Brake Switch indicate CLOSED when the brake pedal is not applied, then indicate OPEN when the brake pedal is applied?		 - Go to Step 17  Go to Step 2 
17 With the scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List in Engine Controls - 4.8L, 5.3L, and 6.0L System OK
scientia non olet · About LEMON Manuals