LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 1998 >> Yukon RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 70 (Automatic Transmission Diagnosis - 4L80-E (Gasoline)) >> Diagnostic Tests >> DTC P0758: 2-3 Shift Solenoid ("B") Electrical Malfunction >> Diagnostic Procedures

Diagnostic Procedures

WARNING: This page does not describe the selected car, but rather 14 other vehicles, including the 1998 GMC Savana Special, 1998 GMC Savana Camper Special, 1998 GMC Savana, 1998 Chevrolet RV Cutaway, and 1998 Chevrolet Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
  1. Connect scan tool to DLC. Turn ignition switch to ON position. DO NOT start engine. Using scan tool, record freeze frame and failure records for reference. Data will be lost when DTCs are cleared later in this test.
  2. If DTCs P0753, P0758 and P1860 are not present, go to next step. If DTCs P0753, P0758 and P1860 are present, remove appropriate2-3 shift solenoid ignition feed circuit fuse from instrument panel fuse block and inspect fuse. See WIRING DIAGRAMS . Replace fuse if necessary, and check for short to ground in wiring harness between transmission 20-pin connector and fuse. Repair wiring as necessary, then go to step 12). If fuse is okay, check for open in wiring harness between transmission 20-way connector and fuse. Repair wire as necessary, then go to step 12).
  3. Using scan tool, command 2-3 shift solenoid on and off 3 times while listening at transmission oil pan. If solenoid does not click when commanded on and off, go to next step. If solenoid clicks when commanded on and off, inspect wiring for poor connections at VCM and transmission 20-pin connector. Check for bent, backed out, deformed or damaged terminals. Repair as necessary, then go to step 12). If connections and terminals are okay, see DIAGNOSTIC AIDS.
  4. Turn ignition off. Disconnect transmission 20-pin connector. Install Jumper Harness (J-39775) to VCM side of transmission 20-pin connector. Connect test light between ground and 2-3 shift solenoid ignition feed circuit (terminal "E") at transmission 20-pin connector. See Figure. Turn ignition switch to ON position. DO NOT start engine.
  5. If test light does not light, check for open or short to ground in ignition feed circuit of 2-3 shift solenoid. Repair as necessary, then go to step 12). If test light lights, connect test light between 2-3 shift solenoid ground circuit and ignition feed circuit (terminals "B" and "E") at transmission 20-pin connector. Using scan tool, command 2-3 shift solenoid on and off 3 times. If test light cycles on and off, go to step 8). If test light does not cycle on and off 3 times, and test light is always on, go to next step. If test light is always off, go to step 7).
  6. Check 2-3 shift solenoid ground circuit for short to ground. Repair circuit as necessary, then go to step 12). If circuit is okay, inspect wiring for poor connections at VCM connector. Check for bent, backed out, deformed or damaged terminals. Repair as necessary, then go to step 12). If connections and terminals are okay, replace VCM, then go to step 12).
  7. Check for open in 2-3 shift solenoid ignition feed circuit or poor connection at VCM connector. Repair circuit as necessary, then go to step 12). If circuit is okay, inspect wiring for poor connections at VCM connector. Check for bent, backed out, deformed or damaged terminals. Repair as necessary, then go to step 12). If connections and terminals are okay, replace VCM, then go to step 12).
  8. Turn ignition off. Disconnect jumper harness from VCM side of transmission 20-pin connector and install harness to transmission side of 20-pin connector. Connect a DVOM between 2-3 shift solenoid ground circuit and ignition feed circuit (terminals "B" and "E") at transmission 20-pin connector.
  9. If resistance is 20-40 ohms, go to next step. If resistance is not 20-40 ohms, disconnect 2-3 shift solenoid connector. Measure resistance between 2-3 shift solenoid terminals. If resistance is 20-40 ohms, check for open circuit in transmission wiring harness. Repair as necessary, then go to step 12). If resistance is not 20-40 ohms, replace2-3 shift solenoid, then go to step 12).
  10. Turn ignition off. Connect a DVOM between ground and 2-3 shift solenoid ground circuit, and between ground and 2-3 shift solenoid ignition feed circuit (terminals "B" and "E") at transmission 20-pin connector. If resistance at both terminals is more than 250 k/ohms, see DIAGNOSTIC AIDS. If resistance at both terminals is less than 250k/ohms, go to next step.
  11. Disconnect 2-3 shift solenoid connector. Measure resistance between ground and each solenoid terminal. If resistance is more than 250 k/ohms, check for short to ground in transmission wiring harness. Repair as necessary, then go to next step. If resistance is less than 250 k/ohms, replace 2-3 shift solenoid, then go to next step.
  12. After repair is complete, select DTC on scan tool. Select "Clear Info" function. Test drive vehicle. Ensure voltage decreases to zero when 2-3 shift solenoid is commanded on, and voltage increases to battery voltage when commanded off. Conditions must be met for 5 seconds. Select "Specific DTC" and enter DTC "P0758". If DTC P0758 is not present, repair is complete. If DTC P0758 is still present, repeat test.
scientia non olet · About LEMON Manuals