LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 1991 >> Value Van 7.4 N >> Repair and Diagnosis >> External Pages >> Different car >> Section 90 (3.8L V6 Gas - VIN [L]) >> Torque Specifications

Torque Specifications

WARNING: This page is about a different car, the 1995 Plymouth Grand Voyager, 1995 Dodge Grand Caravan, and 1995 Chrysler Town & Country. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Air Compressor Bracket-To-Water Pump Bolt 30 (41)
Air Compressor-To-Bracket Bolt 50 (68)
Air Compressor Support Bolt 30 (41)
Air Intake Plenum Bolt (1) 21 (29)
Alternator Bracket-To-Manifold Bolt 40 (54)
Camshaft Sprocket Bolt 40 (54)
Connecting Rod Nut
Step 1 40 (54)
Step 2 Additional 1/4 Turn
Cylinder Head Bolt (2)
Step 1 45 (61)
Step 2 65 (88)
Step 3 65 (88)
Step 4 (3) Additional 1/4 Turn
Engine Bracket Bolt 40 (54)
Exhaust Crossover Pipe Bolt 25 (34)
Exhaust Manifold Bolt 17 (23)
Front Engine Mount Through-Bolt 50 (68)
Front Engine Mount-To-Cylinder Block Bolt 40 (54)
Front Engine Mount-To-Frame Rail Bolt/Nut 40 (54)
Fuel Rail Bolt 17 (23)
Intake Manifold Bolt (4)
Step 1 (5)
Step 2 17 (23)
Step 3 17 (23)
Intake Manifold Brace-To-Cylinder Head Bolt 40 (54)
Left Engine Mount (Flexplate Side) Through-Bolt 55 (75)
Left Engine Mount (Flexplate Side) At Frame Rail Bolt 50 (68)
Main Bearing Cap Bolt
Step 1 30 (41)
Step 2 Additional 1/4 Turn
Oil Pan Drain Plug 25 (34)
Oil Pump Pick-Up Tube Bolt 21 (29)
Right Engine Mount (Timing Chain Side) Through-Bolt 110 (149)
Right Engine Mount (Timing Chain Side) To Side Rail Bolt 50 (68)
Right Engine Mount (Timing Chain Side) Vertical Bolt/Nut 75 (102)
Rocker Arm Shaft Bolt 21 (29)
Spark Plug 20 (27)
Timing Chain Cover Bolt
8 mm Bolt 20 (27)
10 mm Bolt 40 (54)
Torque Converter-To-Flexplate Bolt 55 (75)
Transaxle-To-Cylinder Block Bolt 75 (102)
Vibration Damper Bolt 40 (54)
Water Pump Pulley Bolt 21 (29)
Wheel Lug Nut 95 (129)
INCH Lbs. (N.m) 
Camshaft Position Sensor Bolt 105 (11.9)
Camshaft Thrust Plate Bolt 105 (11.9)
Crankshaft Rear Oil Seal Retainer Bolt 105 (11.9)
Ignition Coil Mounting Bolt 105 (11.9)
Intake Manifold Gasket End Seal Bolt 105 (11.9)
Oil Pan Bolt 105 (11.9)
Pump Cover Bolt 105 (11.9)
Valve Cover Bolt 105 (11.9)
Valve Lifter Yoke Retainer Bolt 105 (11.9)
Water Pump Bolt 105 (11.9)
(1) Tighten bolts to specification in sequence. See Figure.
(2) All bolts except No. 9 (8 mm bolt) must be tightened to specification in sequence. See Figure. No. 9 bolt should be tightened to 25 ft. lbs. (34 N.m) after all other bolts are tightened to specification.
(3) After additional 1/4 turn, bolt torque should exceed 90 ft. lbs. (122 N.m). If torque is not exceeded, replace cylinder head bolt.
(4) Tighten bolts in sequence. See Figure.
(5) Tighten bolts to 10 INCH lbs. (1.1 N.m).