Hydraulic Valve Lifter Adjustment
Rotate engine until rotor is at number 1 cylinder position and points are just opening. With engine at this position, adjust intake valves 1, 2 and 4 and exhaust valves 1, 3 and 5. Back off rocker arm nuts until lash is felt, then tighten nut until all lash is removed and tighten 1 full additional turn. Now rotate engine until rotor is at number 6 position and points are just opening. Following same procedure and adjust intake valves 3, 5 and 6 and exhaust valves 2, 4 and 6.
PISTONS, PINS, RINGS
| Engine | PISTONS | PINS | RINGS | |||||
|---|---|---|---|---|---|---|---|---|
| (1)Clearance | Piston Fit | Rod Fit | Rings | End Gap | Side Clearance | |||
| 1965-67 | ||||||||
| 194" & 230" | .0005-.0011" | .00015-.00025" | .0008-.0016" | 1 | .010-.020" | .0012-.0027" | ||
| 2 | .010-.020" | .0012-.0032" | ||||||
| 3 | .015-.055" | .000-.005" | ||||||
| 250" | .0005-.0011" | .00015-.00025" | .0008-.0016" | 1 | .010-.020" | .0020-.0035" | ||
| 2 | .010-.020" | .0020-.0040" | ||||||
| 3 | .015-.055" | .000-.005" | ||||||
| 292" | .0026-.0032" | .00025-.00035" | .0008-.0016" | 1 | .010-.020" | .0020-.0040" | ||
| 2 | .010-.020" | .0020-.0040" | ||||||
| 3 | .015-.055" | .0005-.0055" | ||||||
| 1968 | ||||||||
| 230" & 250" | .0005-.0011" | .00015-.00025" | .0008-.0016" | 1 | .010-.020" | .0012-.0027" | ||
| 2 | .010-.020" | .0012-.0032" | ||||||
| 3 | .015-.055" | .000-.005" | ||||||
| 292" | .0026-.0032" | .00025-.00035" | .0008-.0016" | 1 | .010-.020" | .0020-.0040" | ||
| 2 | .010-.020" | .0020-.0040" | ||||||
| 3 | .015-.055" | .0005-.0055" | ||||||
| 1969 | ||||||||
| 230" & 250" | .0005-.0014" | .00015-.00025" | .0008-.0016" | 1 | .010-.020" | .0012.0027" | ||
| 2 | .010-.020" | .0012-.0032" | ||||||
| 3 | .015-.055" | .000-.005" | ||||||
| 292" | .0026-.0032" | .00025.00035" | .0008-.0016" | 1 | .010-.020" | .0020-.0040" | ||
| 2 | .010-.020" | .0020-.0040" | ||||||
| 3 | .015-.055" | .0005-.0055" | ||||||
| 1970 | ||||||||
| 250" | .0005.0015" | .00015-.00025" | .0008-.0016" | 1 | .010-.020" | .0012-.0027" | ||
| 2 | .010-.020" | .0012-.0032" | ||||||
| 3 | .015-.055" | .000-.005" | ||||||
| 292" | .0025-.0031" | .00025-.00035" | .0008-.0016" | 1 | .010-.020" | .0020-.0040" | ||
| 2 | .010-.020" | .0020-.0040" | ||||||
| 3 | .015-.055" | .0005-.0055" | ||||||
| 1971-72 | ||||||||
| 250" | .0005-.0015" | .00015-.00025" | .0008-.0016" | 1 | .010-.020" | .0012-.0027" | ||
| 2 | .010-.020" | .0012-.0032" | ||||||
| 3 | .015-.055" | .000-.005" | ||||||
| 292" | .0025-.0035" | .00015-.00025" | .0008-.0016" | 1 | .010-.020" | .0020-.0040" | ||
| 2 | .010-.020" | .0020-.0040" | ||||||
| 3 | .015-.055" | .0005-.0055" | ||||||
| 1973-74 | ||||||||
| 250" | .0005-.0015" | .00015-.00025" | .0008-.0016" | 1 | .010-.020" | .0012-.0027" | ||
| 2 | .010-.020" | .0012-.0027" | ||||||
| 3 | .015-.055" | .000-.005" | ||||||
| 292" | .0026-.0036" | .00015-.00025" | .0008-.0016" | 1 | .010-.020" | .0020-.0040" | ||
| 2 | .010-.020" | .0020-.0040" | ||||||
| 3 | .015-.055" | .0005-.0055" | ||||||
|
||||||||