Diagnostic Trouble Code (DTC) Chart
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| BCM | B14E0:11 | Exterior Lamps Power Supply 'C': Circuit Short To Ground | GO to Pinpoint Test A |
| BCM | B14E0:15 | Exterior Lamps Power Supply 'C': Circuit Short To Battery Or Open | GO to Pinpoint Test A |
| BCM | B14E1:11 | Exterior Lamps Power Supply 'D': Circuit Short To Ground | GO to Pinpoint Test A |
| BCM | B14E1:15 | Exterior Lamps Power Supply 'D': Circuit Short To Battery Or Open | GO to Pinpoint Test A |
| BCM | B1533:02 | Headlamp Switch Module: General Signal Failure | GO to Pinpoint Test A |
| BCM | B1533:08 | Headlamp Switch Module: Bus Signal/Message Failures | GO to Pinpoint Test A |
| BCM | B1533:49 | Headlamp Switch Module: Internal Electronic Failure | GO to Pinpoint Test A |
| BCM | B1533:56 | Headlamp Switch Module: Invalid/Incompatible Configuration | GO to Pinpoint Test A |
| BCM | B1D00:11 | Left Low Beam: Circuit Short To Ground | GO to Pinpoint Test A |
| BCM | B1D00:15 | Left Low Beam: Circuit Short To Battery Or Open | GO to Pinpoint Test A |
| BCM | B1D01:11 | Right Low Beam: Circuit Short To Ground | GO to Pinpoint Test A |
| BCM | B1D01:15 | Right Low Beam: Circuit Short To Battery Or Open | GO to Pinpoint Test A |
| HCM | B1087:83 | LIN Bus 'A': Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test F |
| HCM | B1087:86 | LIN Bus 'A': Signal Invalid | GO to Pinpoint Test F |
| HCM | B1088:83 | LIN Bus 'B': Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test F |
| HCM | B1088:86 | LIN Bus 'B': Signal Invalid | GO to Pinpoint Test F |
| HCM | B14DB:87 | Left Headlamp Driver Control System: Missing Message | GO to Pinpoint Test K |
| HCM | B14DC:87 | Right Headlamp Driver Control System: Missing Message | GO to Pinpoint Test K |
| HCM | B1D64:01 | Left Headlamp Swiveling Motor: General Electrical Failure | GO to Pinpoint Test F |
| HCM | B1D64:87 | Left Headlamp Swiveling Motor: Missing Message | GO to Pinpoint Test F |
| HCM | B1D65:01 | Right Headlamp Swiveling Motor: General Electrical Failure | GO to Pinpoint Test F |
| HCM | B1D65:87 | Right Headlamp Swiveling Motor: Missing Message | GO to Pinpoint Test F |
| HCM | B1D68:64 | Left Headlamp Swiveling Feedback Sensor: Signal Plausibility Failure | GO to Pinpoint Test F |
| HCM | B1D69:64 | Right Headlamp Swiveling Feedback Sensor: Signal Plausibility Failure | GO to Pinpoint Test F |
| HCM | U0100:87 | Lost Communication With ECM/PCM 'A': Missing Message | GO to Pinpoint Test L |
| HCM | U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': Missing Message | GO to Pinpoint Test M |
| HCM | U0122:87 | Lost Communication With Vehicle Dynamics Control Module: Missing Message | GO to Pinpoint Test N |
| HCM | U0131:87 | Lost Communication With Power Steering Control Module 'A': Missing Message | GO to Pinpoint Test O |
| HCM | U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to Pinpoint Test P |
| HCM | U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test Q |
| HCM | U0212:87 | Lost Communication With Steering Column Control Module: Missing Message | GO to Pinpoint Test R |
| HCM | U023A:87 | Lost Communication With Image Processing Module A: Missing Message | GO to Pinpoint Test S |
| HCM | U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test H |
| HCM | U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information | GO to Pinpoint Test H |
| HCM | U0416:00 | Invalid Data Received From Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test H |
| HCM | U0420:00 | Invalid Data Received from Power Steering Control Module 'A': No Sub Type Information | GO to Pinpoint Test H |
| HCM | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test H |
| HCM | U0429:00 | Invalid Data Received From Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test H |
| HCM | U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test H |
| HCM | U053B:00 | Invalid Data Received From Image Processing Module A: No Sub Type Information | GO to Pinpoint Test H |
| HCM | U2024:51 | Control Module Cal-Config Data: Not Programmed | GO to Pinpoint Test G |
| HCM | U2024:57 | Control Module Cal-Config Data: Invalid/Incompatible Software Component | GO to Pinpoint Test G |
| HCM | U202B:61 | In-Use Application Signing Key: Signal Calculation Failure | GO to Pinpoint Test G |
| HCM | U202B:62 | In-Use Application Signing Key: Signal Compare Failure | GO to Pinpoint Test G |
| HCM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test G |
| HCM | U2101:56 | Control Module Configuration Incompatible: Invalid/Incompatible Configuration | GO to Pinpoint Test G |
| HCM | U2200:45 | Control Module Configuration Memory Corrupt: Program Memory Failure | GO to Pinpoint Test G |
| HCM | U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test G |
| HCM | U3000:45 | Control Module: Program Memory Failure | GO to Pinpoint Test G |
| HCM | U3000:46 | Control Module: Calibration/Parameter Memory Failure | GO to Pinpoint Test G |
| HCM | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test I |
| HCM | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test J |
| LDCMA | B123A:87 | Left Front Turn Indicator: Missing Message | GO to Pinpoint Test K |
| LDCMA | B124B:87 | Left Daytime Running Light: Missing Message | GO to Pinpoint Test K |
| LDCMA | B149E:87 | Left Front Position/Sidemarker: Missing Message | GO to Pinpoint Test K |
| LDCMA | B14E5:56 | Left Front Enhanced Exterior Lighting System: Invalid/Incompatible Configuration | GO to Pinpoint Test T |
| LDCMA | B14E5:96 | Left Front Enhanced Exterior Lighting System: Component Internal Failure | GO to Pinpoint Test T |
| LDCMA | B1566:87 | Left Front Static Bending Lamp Output: Missing Message | GO to Pinpoint Test K |
| LDCMA | B1A57:87 | Left Headlamp Leveling Motor: Missing Message | GO to Pinpoint Test K |
| LDCMA | B1D00:11 | Left Low Beam: Circuit Short To Ground | GO to Pinpoint Test A |
| LDCMA | B1D00:12 | Left Low Beam: Circuit Short To Battery | GO to Pinpoint Test A |
| LDCMA | B1D00:13 | Left Low Beam: Circuit Open | GO to Pinpoint Test A |
| LDCMA | B1D00:14 | Left Low Beam: Circuit Short To Ground Or Open | GO to Pinpoint Test A |
| LDCMA | B1D00:16 | Left Low Beam: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| LDCMA | B1D00:1E | Left Low Beam: Circuit Resistance Out Of Range | GO to Pinpoint Test A |
| LDCMA | B1D00:4B | Left Low Beam: Over Temperature | GO to Pinpoint Test A |
| LDCMA | B1D00:62 | Left Low Beam: Signal Compare Failure | GO to Pinpoint Test A |
| LDCMA | B1D00:87 | Left Low Beam: Missing Message | GO to Pinpoint Test A |
| LDCMA | B1D00:87 | Left Low Beam: Missing Message | GO to Pinpoint Test K |
| LDCMA | B1D02:11 | Left High Beam Circuit: Circuit Short To Ground | GO to Pinpoint Test B |
| LDCMA | B1D02:12 | Left High Beam Circuit: Circuit Short To Battery | GO to Pinpoint Test B |
| LDCMA | B1D02:13 | Left High Beam Circuit: Circuit Open | GO to Pinpoint Test B |
| LDCMA | B1D02:14 | Left High Beam Circuit: Circuit Short To Ground Or Open | GO to Pinpoint Test B |
| LDCMA | B1D02:16 | Left High Beam Circuit: Circuit Voltage Below Threshold | GO to Pinpoint Test B |
| LDCMA | B1D02:1E | Left High Beam Circuit: Circuit Resistance Out Of Range | GO to Pinpoint Test B |
| LDCMA | B1D02:4B | Left High Beam Circuit: Over Temperature | GO to Pinpoint Test B |
| LDCMA | B1D02:87 | Left High Beam Circuit: Missing Message | GO to Pinpoint Test B |
| LDCMA | B1D02:87 | Left High Beam Circuit: Missing Message | GO to Pinpoint Test K |
| LDCMA | U0241:00 | Lost Communication With Headlamp Control Module 'A': No Sub Type Information | GO to Pinpoint Test K |
| LDCMA | U0273:00 | Lost Communication With Lighting Driver Control Module 'A': No Sub Type Information | GO to Pinpoint Test T |
| LDCMA | U0542:00 | Invalid Data Received From Headlamp Control Module 'A': No Sub Type Information | GO to Pinpoint Test K |
| LDCMA | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test U |
| LDCMA | U3000:45 | Control Module: Program Memory Failure | GO to Pinpoint Test U |
| LDCMA | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test T |
| LDCMA | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test T |
| LDCMA | U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test T |
| LDCMA | U3003:A3 | Battery Voltage: System Voltage High | GO to Pinpoint Test T |
| LDCMB | B123B:87 | Right Front Turn Indicator: Missing Message | GO to Pinpoint Test K |
| LDCMB | B124A:87 | Right Daytime Running Light: Missing Message | GO to Pinpoint Test K |
| LDCMB | B149F:87 | Right Front Position/Sidemarker: Missing Message | GO to Pinpoint Test K |
| LDCMB | B14E7:56 | Right Front Enhanced Exterior Lighting System: Invalid/Incompatible Configuration | GO to Pinpoint Test T |
| LDCMB | B14E7:96 | Right Front Enhanced Exterior Lighting System: Component Internal Failure | GO to Pinpoint Test T |
| LDCMB | B1568:87 | Right Front Static Bending Lamp Output: Missing Message | GO to Pinpoint Test K |
| LDCMB | B1A58:87 | Right Headlamp Leveling Motor: Missing Message | GO to Pinpoint Test K |
| LDCMB | B1D00:62 | Left Low Beam: Signal Compare Failure | GO to Pinpoint Test A |
| LDCMB | B1D01:11 | Right Low Beam: Circuit Short To Ground | GO to Pinpoint Test A |
| LDCMB | B1D01:12 | Right Low Beam: Circuit Short To Battery | GO to Pinpoint Test A |
| LDCMB | B1D01:13 | Right Low Beam: Circuit Open | GO to Pinpoint Test A |
| LDCMB | B1D01:14 | Right Low Beam: Circuit Short To Ground Or Open | GO to Pinpoint Test A |
| LDCMB | B1D01:16 | Right Low Beam: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| LDCMB | B1D01:1E | Right Low Beam: Circuit Resistance Out Of Range | GO to Pinpoint Test A |
| LDCMB | B1D01:4B | Right Low Beam: Over Temperature | GO to Pinpoint Test A |
| LDCMB | B1D01:87 | Right Low Beam: Missing Message | GO to Pinpoint Test A |
| LDCMB | B1D01:87 | Right Low Beam: Missing Message | GO to Pinpoint Test K |
| LDCMB | B1D03:11 | Right High Beam Circuit: Circuit Short To Ground | GO to Pinpoint Test B |
| LDCMB | B1D03:12 | Right High Beam Circuit: Circuit Short To Battery | GO to Pinpoint Test B |
| LDCMB | B1D03:13 | Right High Beam Circuit: Circuit Open | GO to Pinpoint Test B |
| LDCMB | B1D03:14 | Right High Beam Circuit: Circuit Short To Ground Or Open | GO to Pinpoint Test B |
| LDCMB | B1D03:16 | Right High Beam Circuit: Circuit Voltage Below Threshold | GO to Pinpoint Test B |
| LDCMB | B1D03:1E | Right High Beam Circuit: Circuit Resistance Out Of Range | GO to Pinpoint Test B |
| LDCMB | B1D03:4B | Right High Beam Circuit: Over Temperature | GO to Pinpoint Test B |
| LDCMB | B1D03:87 | Right High Beam Circuit: Missing Message | GO to Pinpoint Test B |
| LDCMB | B1D03:87 | Right High Beam Circuit: Missing Message | GO to Pinpoint Test K |
| LDCMB | U0242:00 | Lost Communication With Headlamp Control Module 'B': No Sub Type Information | GO to Pinpoint Test K |
| LDCMB | U0274:00 | Lost Communication With Lighting Driver Control Module 'B': No Sub Type Information | GO to Pinpoint Test T |
| LDCMB | U0543:00 | Invalid Data Received From Headlamp Control Module 'B': No Sub Type Information | GO to Pinpoint Test K |
| LDCMB | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test U |
| LDCMB | U3000:45 | Control Module: Program Memory Failure | GO to Pinpoint Test U |
| LDCMB | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test T |
| LDCMB | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test T |
| LDCMB | U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test T |
| LDCMB | U3003:A3 | Battery Voltage: System Voltage High | GO to Pinpoint Test T |
| SCCM | B124C:96 | Turn Indicator Stalk Switch Pack: Component Internal Failure | GO to Pinpoint Test E |
| SCCM | B124C:9E | Turn Indicator Stalk Switch Pack: Stuck On | GO to Pinpoint Test E |